Being under stress can cause you to miss meals, eat on the move, or bolt your food.
压力之下会造成错过进餐、边做事边吃、或者吞吃食物。
So, in the same bolt tension narrow narrow smooth after the pressure stress increases.
这样，在螺栓张力相同的情况下，缩小后的窄光滑面的压紧应力就会增大。
Under the action of tensile stress and tensile stress, the bolt with relatively low strength will crack first, and then the fatigue fracture will occur.
在拉应力和应拉力交替的作用下，强度相对较低的螺栓会先产生裂纹，进而发生疲劳断裂。
It is shown that the characteristics of shear stress acting on bolt vary in different zones zone of surrounding rock and are reflected in the axial stress distribution of bolt.
结果表明，在围岩不同区内，锚杆所受剪切力具有不同的特点，而且，锚杆所受剪切的特点在锚杆轴力分布中得到了反映。
The monitoring project of Zhouning Hydropower station underground plant and water intake system including monitoring of the surrounding rock deformation, bolt stress, osmotic pressure and joint.
周宁水电站地下厂房及引水系统的监测项目包括围岩变形监测、锚杆应力计监测、渗透压力监测、测缝计监测。
It is concluded that, the residual stress induced by cold expansion can maintain enough strength to prevent and retard fatigue crack initiation and growth in rail bolt hole.
结果表明，冷扩张过程所引入的切向残余压应力能保持足够的强度，以对钢轨螺栓孔起到显著的防裂和止裂作用。
It revealed that alternating stress in long time cause the bolt fatigue failure, meanwhile the failure process was also effected by superheating steam.
认为主要原因是螺栓在长期服役中受交变应力引起疲劳失效所致。过热蒸汽介质对疲劳失效有影响。
By computer simulation, we analysis and study the law of wall rock stress distribution, deformation, the axial force of bolt and the roof-off-strata.
通过计算机数值模拟分析研究了锚杆支护回采巷道围岩应力分布、围岩变形、锚杆轴力及顶板离层规律。
By analysis, bolt fatigue stress is marginally high.
通过计算分析，螺栓的疲劳应力稍偏高。
In order to ensure the reliability of flywheel bolt connection, stress analysis of bolt is performed using contact analysis method.
为了确保飞轮螺栓连接的可靠性，采用接触分析法对螺栓进行了应力分析。
Stress relaxation should be taken into consideration while designing tight bolt connection under a high temperature. The paper discusses the calculation thought and solution about stress relaxation.
在高温环境下有紧密性要求的螺栓联接，在设计时应考虑应力松弛。讨论了关于应力松驰问题的计算思路和解决方法。
As the bolt tension increase, the tension of rail web, stress of joint bar and stress of joint bolt would increase accordingly, but the displacement of rail would become smaller.
螺栓扭矩增大，接头区钢轨轨腰拉力、夹板应力、螺杆内应力都会增大，而钢轨位移会随着螺栓扭矩的增大而减小。
The contact finite element method is used in present paper to analyze stress of bolt connection structure.
应用接触有限元方法，对螺栓联接结构进行了应力分析。
On the basis of relationship between bolt axial stress and rate of change in ultrasonic wave transmission time, the author has developed a device to directly measure axial stress in bolts.
根据螺栓的轴向应力与超声波传播时间变化率的关系，作者研究了一种可直接测量螺栓轴向应力的仪器。
The pretightening force of FRP construction bolt joint has been researched in the theory of bolt washer stress.
应用螺栓-垫圈应力理论对FRP结构搭接点预紧力进行了研究。
If the stress produced by the additional bending moment is too large, the bolt will break.
如果附加弯矩产生的应力过大，螺栓便会断裂。
The results indicate that it is essential to revise the bolt stress by using the formulas when rock mass is in plastic state.
结果显示，当岩体进入塑性、变形较大时，用推导公式对锚杆变形、应力进行修正是非常必要的。
We think that the method of estimating maximal pre-applied stress of the working bolt can provide a reference for preventing further fatigue fracture of boxter bolts.
认为用估算螺栓工作时的最大预紧应力的方法，对防止埋头螺栓疲劳断裂再次重复发生有一定的参考价值。
This paper focuses on the effects of the distributed bolts and bolt-holes on the shell flange-end bending stress, and suggests a more practical calculation model on shell-end stress.
本文着重分析了离散分布的螺栓及螺栓孔对筒体端部应力的影响，对筒体端部的应力计算提出了一个更接近实际的计算模型。
This paper summarizes simply the history of bolt testing technique, describes in detail stress wave reflection method.
笔者对锚杆检测技术的历史进行了简单的总结，并详细、重点介绍了目前被广泛使用的应力波反射法。
This paper analyses the special points and mechanism of bolt connection mode on type HXD1 locomotive traction base, and shows the effect of bush to bolt application reliability by stress calculation.
分析HXD1型机车牵引座的螺栓连接方式中的特殊点及其机理，并通过受力计算说明了衬套对螺栓使用可靠性的影响。
By using the finite element method, the dynamic stress caused by vertical contact impact between bolt locking surface and barrel extension locking surface of a new rifle was studied.
采用有限元方法研究了某新型自动步枪枪机闭锁面与节套闭锁面间垂直接触碰撞的动应力。
Thus, under the same bolt tension, reduce narrow smooth surface after the compressive stress will increase.
这样，在螺栓张力相同的情况下，缩小后的窄光滑面的压紧应力就会增大。
An improved method of stress analysis about bolt screw with interference fitting is provided as the first step of fatigue life-prediction for the joint.
针对过盈螺纹的疲劳寿命估算进行了工作，求解应力是寿命估算的第一步。
According to the numerical simulation of heavy-duty diesel engine to raise power, two methods to assess the strength of cylinder head bolt, static calculation and fatigue stress check, are introduced.
结合大功率柴油机提升功率的数值计算工作，介绍了评估气缸盖螺栓强度的两种方法：静强度分析法和疲劳强度校核法。
Manufacture method of anchor bolt plate is introduced and stress distribution in laboratory is analyzed in this paper.
介绍了锚杆测力托盘的制作方法，在实验室对锚杆托盘的应力分布进行了分析。
Aging treatment is performed for microalloyed steel for cold hardening bolt, which can stabilize its microstructure, enhance its strength and reduce its residual stress.
冷作强化非调质钢螺栓经时效处理可以稳定组织、提高强度、降低残余应力。
Aging treatment is performed for microalloyed steel for cold hardening bolt, which can stabilize its microstructure, enhance its strength and reduce its residual stress.
冷作强化非调质钢螺栓经时效处理可以稳定组织、提高强度、降低残余应力。
应用推荐