The strength, rigidity, stability and torsional rigidity of the bodywork structure were calculated by using finite element analysis. Thus the optimum fillet of the bodywork structure can be specified.
采用有限单元法对车体结构的强度、刚度、稳定性、挠跨比、扭转刚度进行计算，为车体设计提供了参考依据。
We ran finite element analysis stress calculations to determine where the frame needed to be reinforced for maximum strength and stiffness, then reinforced those areas with additional carbon fiber.
我们跑应力有限元分析计算，确定了框架需要得到加强的最大强度和刚度，然后加强这些领域更多的碳纤维。
Based on the results of experiment and finite element analysis, the shear strength and the effect of reinforcement of the perforated brick walls are also discussed.
本文还根据试验结果和有限元法分析，探讨了空心砖墙的抗剪强度和横向、纵向配筋效应。
Lastly the Finite Element Method (FEM) is applied to analysis and checking the strength of pipeline.
应用有限元方法来分析校核管线的强度。
The author applied ANSYS finite-element standard calculation software through the strength analysis, which assured the reliability of the analysis.
在整个强度分析中，作者应用了ANSYS有限元标准计算软件，保证了分析的可靠性。
Lastly, the strength analysis of the guide frame, which is key part to link guide tire sets and vehicle body, is carried out by finite element method software (ANSYS).
最后利用有限元软件(ANSYS)对连接导向轮系和车身的关键部件——导向架进行应力强度分析。
In paper, the structural static strength and dynamic characteristic of pole? Tower of aerial power? Delivery line are analyzed and discussed with the finite element analysis.
主要利用有限元方法对架空送电线路杆塔进行结构强度和结构动力学特性分析。
Based on completion of wall strength calculation, then do the finite element stress analysis.
在完成管壁强度计算的基础上，进行管壁有限元应力分析。
Through the visualization software VB connecting and invoking the ANSYS, they realize the finite element strength analysis of the bus frame.
通过可视化软件VB与ANSYS连接和调用，实现客车骨架强度的有限元分析的可视化。
The finite element method has been used in strength analysis for a wire reel of ship elevator.
用有限单元法对缠绕式升船机卷筒的强度进行了分析计算。
Finite element method is an important tool for the strength analysis of loader structures.
有限元法是装载机结构强度分析的有力工具。
The paper analysis strength of the vibrating screen, put forward improving method for its structure, with the dynamic finite element method and dynamic measure.
本文用动态有限元理论计算及在线测试分析方法，对振动筛的强度作了分析，提出了筛体结构的改进方法。
Meanwhile, it applies the finite element analysis to make strength check, the result satisfies the strength requirement.
同时采用了有限元的分析方法对其进行强度校核，结果满足强度要求。
On the basis of the method, the FEA (finite element analysis) model of the van body in extendable work condition is established and the structure strength analysis of the van body is proceeded.
在此方法基础上建立了扩展厢式车厢体展开状态下有限元模型，并对其进行了强度分析。
A reasonable result of frame strength analysis was obtained by both the photoelasticity and finite element methods.
利用光弹性力学、有限元计算方法，进行强度分析取得了可靠的分析结果。
This paper analyzed the effect of corroded flaw interaction on remaining strength of line pipe with the finite element (FEM) analysis method.
采用有限元数值计算方法分析了腐蚀坑交互作用对管道剩余强度的影响。
Then, by using beam element and MPC184 element, the finite element model for strength analysis was setup and simplified.
然后利用梁单元和MPC184单元，建立了供强度计算的有限元模型并进行了简化。
The load analysis and calculation under wave action of this platform is developed, on this base, a three dimensional finite element strength analysis for main structural body is conducted.
展开了对该平台在波浪作用下载荷的分析计算，在此基础上对主体结构进行了三维有限元强度分析。
The finite element analysis of the wheel rail contact shows that the maximum stress under the subsurface exceeds first yield strength, which leads to plastic deformation.
在对轮-轨系统进行有限元分析的基础上，研究了轨道的受力情况和摩擦系数对应力分布的影响，讨论了轨道的弹塑变形和安定极限。
The finite element method is applied to analysis and optimize the design of the hydrogenation reactor skirt support area, and stress of the risk section is assessed and strength is checked.
采用有限元法对加氢反应器裙座支撑区进行有限元分析及优化设计，并对其危险截面作应力评定和强度校核。
The structural features of a new type of railcar bogies are described. And the finite element strength analysis is made on the frame assembly.
介绍了一种新型轨道车辆转向架的结构特点，并对其构架总成进行了有限元强度分析。
The stress concentration analysis was done by the finite element method and boundary element method. The fatigue strength and the strength under the static load were calculated.
对螺纹槽管进行了疲劳强度计算，并采用边界元和有限元法对螺纹槽管的应力集中进行了数值分析及静载强度计算。
This topic can use the Finite element to analysis the strength of the derrick and the mobile shelf.
本课题通过有限元方法对井架和车架进行强度分析。
By means of finite element method, the strength analysis of light frame has been executed, and the result verifies the rationality of structure design.
采用有限元法对构架强度进行了计算分析，在对轻型构架的强度和力学特性有一定认识的同时，验证了结构设计的合理性。
Based on the second-order perturbation technique, the stochastic finite element method (SFEM) of the strength analysis of the turbine blade is introduced in this paper.
本文基于二阶摄动技术研究叶片强度分析的随机有限元方法。
A new type of clutch flywheel needs to determine the limited strength under high centrifugal stress. Finite element analysis and burst spin tests of the flywheels has been done.
为确定一种离合器飞轮新产品在大离心力作用下的总体强度储备，对飞轮在离心力场及配合应力作用下的应力分布作有限元分析，并进行了超速破坏试验。
Described are the lightening design, energy absorption car-body design, finite element analysis, static strength test and modal analysis calculation.
介绍了北京八通线地铁车体钢结构的轻量化设计、吸能车体设计、有限元分析、静强度试验和模态分析计算。
Using I-DEAS software, finite element analysis of static strength of low-sided weathering steel gondola car body is carried out.
利用I -DEAS软件，对低边耐候钢敞车车体钢结构进行有限元静强度分析。
In this paper, for strength analysis of cylindrical shells, model of ringed spline finite super - element is given.
提出一环状样条超级单元用于圆柱壳的分析。
In this paper, for strength analysis of cylindrical shells, model of ringed spline finite super - element is given.
提出一环状样条超级单元用于圆柱壳的分析。
应用推荐