This paper analyzes the error of torque sensor of strain-resistor which derives from the influences of bending moment on elastic axis, and discusses the Eliminating techniques.
本文对在应用应变式扭矩传感器时由于在弹性轴上的弯矩而引起的误差进行了力学分析，并提出了消除的方法。
These formulae give us the stress and strain in a prismatic beam when it is subjected to pure bending .
当棱柱形梁受纯弯曲时，这些公式给出了它的主力和主变。
This paper delivered the relationships of uniaxial tensile and compressive stress with strain and bending properties, and felt-bending strength of cement mortar with polyvinyl acetate (PVAC).
研究掺聚醋酸乙烯水泥砂浆的轴拉和轴压应力—应变关系、抗弯性能以及长期粘结抗弯强度。
The bending and shear modifying coefficients are derived according to the distribution of the stress and strain of the sandwich plate along the direction of the plate thickness.
根据夹层板的正应力、正应变和剪应力、剪应变沿板厚的分布关系，得到夹层板的弯曲、剪切修正系数。
The computation expression for the strain neutral layer of stress and plastic bending was introduced and so the thinning coefficient computing formula of sheet metal was deduced.
给出了板料弯曲的应力应变中性层和纯弯曲应变中性层的计算公式，并推出板料弯曲时的变薄系数计算公式。
The methods of compressing strain energy and bending strain energy are adopted to study low temperature performance of montmorillonite modified asphalt with two different montmorillonites by indoo.
通过两种武汉市售蒙脱土和实验室纯化蒙脱土，采用压缩应变能、弯曲应变能的方法，进行蒙脱土改性沥青低温性能研究。
It utilized the microbend loss resulting from optical fiber bending to measure the change of environmental parameters, such as pressure, temperature, acceleration, strain and flow.
光纤微弯传感器是一种强度调制式光纤传感器，它是利用光纤的微弯损耗效应来测量压力、温度、加速度、应变、流量等环境参量的变化。
Series solutions were derived for the in-plane strain, deflection and bending strain that satisfy the simplified boundary conditions to calculate the shear lag coefficient.
根据简化的边界条件，得到了面内应变和弯曲应变的级数解，进而求得剪力滞后系数。
An assumed strain finite element method based on the theory of strain gradient was proposed to explore the size effect that frequently exhibited in micro-beam bending.
采用基于应变梯度理论的假设应变有限元方法研究了微尺度梁弯曲的尺寸效应。
To generate the required bending strain, a slit is cut on one side to create bending bridge on the opposite side, to which a strain gage is bonded.
以产生所需的弯曲应变，狭缝是削减对一方创造弯曲大桥的对岸，一个应变片是保税区。
In the method the modal strain energy of an element is divided into tension modal strain energy, torsion modal strain energy and bending modal strain energy.
该方法将单元模态应变能分解为拉压、扭转和弯曲模态应变能，利用单元的主要模态应变能分量与结构固有频率的改变量对结构裂纹位置进行识别。
Reduced integrated quadratic shell element S8R5 can provide accurate solution for small strain membrane bending problem.
减缩积分二次单元S8R5对于小应变薄膜弯曲问题的模拟能给出精确解。
Through measuring deflection and strain of test girders under loading, performances of this type of box girder, including bending, torsion and distortion are analyzed.
通过测试模型梁在静力荷载作用下的挠度和应变，来分析这种箱梁结构的弯曲、扭转和畸变等力学特性。
This paper shows that the shear stress distribution in bending layer has similar characteristics as the strain distribution near the ends of the actuator.
通过分析可得，粘贴层剪切应力的分布与致动器端部附近的应变分布有相似的特征。
The experimental results present that the strain of optic fiber Fabry-Perot sensor is better linear with loading of bending beam.
智能夹层中光纤法珀腔传感器的应变与载荷之间具有良好的线性关系。
Objective To study the effect of the number of screws on the bending stiffness and dynamic compression plate (DCP) strain in a transverse fracture model in vitro.
目的研究体外模拟横断骨折模型中螺钉数量对动力加压钢板(DCP)应变和弯曲刚度的影响。
Adopting this method not only can analyze instantaneous strain condition and evolution during tube bending, but also can analyze deforming feature.
采用该方法不仅可以分析弯管成形过程瞬时应变状态及其演化过程，而且可以分析弯管成形过程变形特点。
In this paper, the test results of bending concrete specimens are shown, and the vlues of plane-strain fracture toughness, calculated by four different methods, are compared with one another.
本文，对混凝土弯曲试样进行了测试，并用四种不同的方法进行了平面应变断裂韧性的计算和比较。
The stress and strain of the vehicle frame when bearing bending loads and bending-torsion loads are analyzed.
分析了甘蔗种植机机架在弯曲和扭转组合工况下的应力和应变分布。
Based on lots of tube bending experiments, the stress-strain state along the tangential direction of bending line and the direction of the wall thickness is analyzed.
通过大量管材弯曲试验，分析了沿弯曲线的切向和管壁厚方向的应力应变状态，给出弯管内、外侧管壁厚变化量和切向应变的近似计算公式。
A few methods, which approximately calculate minimum relative bending radius, are put forward by analyzing the stress and strain as plate bending deformation in this paper.
通过对板料弯曲变形应力应变分析，提出了几种近似计算最小相对弯曲半径的方法。
Using the criterion of "minimum bending strain energy", the optimum hoisting points of the column are determined with the method of "three step cycling coordinate search".
以“弯曲应变能最小”为优化准则、采用“三步循环坐标搜索法”求解最优吊点坐标。
The influence of axial force on the elastic-plastic stretch bending and sprngbackof a sheet metal is examined and a method to calculate the strain of middle layer is also given.
通过对带钢横截面上应力状态的分析，研究了纵向拉力对带钢变形的影响，给出了计算带钢中性层应变的方法。
In these experiments, specimens were bending to produce different pre-strain respectively, and then reverse bending were taken one by one.
在各弯曲试样得到不同的预应变后，又对其进行反向加载，记录不同预应变下各试样反向加载的弯矩随表面应变的变化曲线。
Grows according to the baby, the science determined that the hard soft sufficiency, the scattered baby whole body pressure, prevents the vertebra bending strain;
依照婴儿成长，科学确定硬软适应度，分散婴儿全身压力，防止脊椎弯曲变形；
Based on a series of fatigue tests, the change laws and the main influence factors of FRP strain of strengthened RC beams under cyclic bending loads were analyzed.
根据一系列常幅疲劳试验，分析了抗弯加固rc梁中FRP疲劳应变的变化规律和关键影响因素。
Tests of measuring torque moment verified that circuits with four strain gauges could get rid of the influence exerted by the bending moment.
介绍了三种测应变的线路，通过实验证实，在测扭矩时，用4片电阻应变片构成的线路，可以排除弯矩的影响。
Tests of measuring torque moment verified that circuits with four strain gauges could get rid of the influence exerted by the bending moment.
介绍了三种测应变的线路，通过实验证实，在测扭矩时，用4片电阻应变片构成的线路，可以排除弯矩的影响。
应用推荐