The measuring principle, system composition and measuring error analysis of the computer controlled step shaft multi parameters on line measuring system are introduced.
介绍了微机控制的阶梯轴多参数在线测量系统的测量原理、系统构成及测量误差分析。
The next step is to test the strength of the shaft.
下一步将是测试吊杆的强度。
A two-step forging approach was taken in the production of GH4169 turboshaft of an engine, which was an integration of a disk and a shaft.
某发动机用GH4169合金涡轮轴转动锻件由轴部和盘部两部分组成，考虑采用两步锻造法进行生产。
In this step, work to drill for the pipe of a propeller shaft or a rudder.
在这个步骤中，演练工作，为管道的传动轴或舵。
Each input of a pulse motor shaft of a step Angle stepping increment.
每输入一个脉冲电机转轴步进一个步距角增量。
Distal locking is one challenging step during intramedullary nailing of femoral shaft fractures that can lead to an increase of radiation exposure.
在股骨干骨折的患者打髓内钉时，远端锁定是非常有挑战性的一步，且该过程会增加射线的照射。
Some main processing parameters are briefly introduced, such as speed of main shaft, feed rate, shape of spinning wheel, deformation rate of each step and structure of template.
对主要工艺参数如主轴转速、进给率、旋轮形状、道次变形率、模板形式等作了简要介绍。
It can calculate the torsion rigidity of the variable section step-shaft simply using the general formula for calculating the same diameter shaft which can be found directly in material mechanics.
从而可利用材料力学中求解等直径圆轴扭转刚度的一般公式简便地求出变截面阶梯轴的扭转刚度。
The traditional process step of maching shaft material cannot conform to the technical requirements, because of the higher precision required by distributor shaft.
分电器轴的加工精度要求较高，传统的轴下料加工工序不能满足其工艺要求。
The first step is to close all vents and openings at the top of the hoistway to prevent water from entering the elevator shaft.
第一步是关紧电梯井道上方所有的排气口以及出口，防止水进入电梯井道。
Based on this view, the multi-step straightening stroke algorithm was built up to the shaft with single-edged crack.
基于这一观点，结合校直行程递推算法，建立了单边径向裂纹轴的多步校直行程递推算法。
An assembly step matching the shaft shoulder of the mainshaft is positioned on the shaft sleeve and a fixed gap forms between the shaft sleeve step and the water-tight plate.
轴套上设有与主轴轴肩配置的装配台阶，轴套台阶与水密封板之间形成有固定的间隙。
On the reservation of original thought of the system software, this paper adjusts the software architecture of motion control task, and re-plans the driven strategy of shaft motor and step motors.
在保留原先控制系统软件流程宏观设计思路的前提下，对运动控制任务的软件架构进行了调整，对运动控制作业进行了重新规划。
Shape Optimization of Transition Curve of Shoudle of Step-Shaped Shaft and Its Experimental Research;
屈服点是弹性变形区域到塑性变形区域之间曲线的过渡点。
Shape Optimization of Transition Curve of Shoudle of Step-Shaped Shaft and Its Experimental Research;
屈服点是弹性变形区域到塑性变形区域之间曲线的过渡点。
应用推荐