Fourth, there are loose steering arm down.
第四，转向垂臂有松动。
The term tiller is also used for the steering arm of small outboard engines.
tiller这个术语也用来指舷外发动机的掌舵臂。
The tie rod at each end of the rack connects to the steering arm on the spindle.
齿条一端连着拉杆，拉杆与车轮轴上的转向摇臂相连接。
Situate the newly completed Steering Arm into the handlebar clamp as shown below.
位于车把夹如下所示的新进转向臂完成。
In addition, the brake lever must be bent so that it can clear the steering arm weldment.
此外，必须刹车杆弯曲，以便它可以清除转向臂焊件。
Turn the adjustment screw so that the steering arm moves away from the main motor. Keep turning until you hear a metallic sound created when the discs come together.
旋动调节螺杆使转向臂向主电机反方向移动，继续转动调节螺杆直到动盘与定盘接触，发出轻微金属碰撞声为止。
It consists of steering wheel steering shaft worm gear sector pitman arm drag link steering knuckle arm king pin steering arms tie rod front axle and steering knuckle.
转向系统包括转向盘、转向轴、蜗杆、扇形齿轮、转向摇臂、直拉杆、转向节臂、主销、转向臂、转向直拉杆、前轴和转向节。
It consists of steering wheel steering shaft worm gear sector pitman arm drag link steering knuckle arm king pin steering arms tie rod front axle and steering knuckle.
转向系统包括转向盘，转向轴，蜗杆，扇形齿轮，转向摇臂，直拉杆，转向节臂，主销，转向臂，转向直拉杆，前轴和转向节。
Ball and socket joints let your arm bones rotate at the shoulders and also allow the wheels of your car to be turned through the steering column.
球状关节是的人类上肢骨骼可以在肩部自由旋转，这也是汽车车轮在转向柱的操控下转向的关键所在。
With the older cars you have to use what I call arm-strong steering.
开老爷车，你得使用我说的那种‘手臂助力方向盘’。
All Thunderbolt Steering configurations use this assembly. Therefore, a left and right arm are required.
所有迅雷督导配置使用此程序集。因此，左，右手臂是必需的。
Not as popular as Under Seat Steering, due to arm fatigue or lack of intuitive design.
不是受欢迎座椅指导下，由于手臂疲劳或设计缺乏直观。
On the contrary, if the seat steering wheel is too close, grasp the steering wheel bending the arm after will be very big, crash, it is almost no space curved, also it is easy to fracture.
相反，若座椅距离转向盘太近，把握转向盘后手臂的弯曲度会很大，撞车时，它就几乎没有弯曲空间了，同样会很容易骨折。
If seat away from the steering wheel, the arm unbend, almost crash straight arm is easy to break.
若座位远离转向盘，则手臂几乎伸直，撞车时直来直去的手臂很容易折断。
Specially manufacture automotive Chassis fittings, Steering parts, Ball joint, Tie rod end, Side rod Assy, Rock and Stabilizer link, Control arm, Idler arm, Pitman arm, Center link cross rod.
专业制造汽车底盘部件和转角及转动部件，产品有：悬挂球头、拉杆球头、控制臂球头、转角拉杆球头、拉杆总成、主邦汰、副邦汰等系列。
Moreover, increasing the stiffness and damping of lower control arm rear bushing and the steering column inertia can effectively reduce the shimmy caused by brake judder.
此外，增加前悬吊下控臂后衬套的刚性系数、阻尼系数与方向盘的转动惯量，均可有效减少因煞车抖振所导致的方向盘振动。
It is one of trailing arm suspension that can only be applied in the rear axle and cannot be applied in the front steering axle, so there are only two wheel alignment parameters: toe-in and camber.
它属于纵臂式悬架，只能用于后轮，且不能用于转向轮，因此其定位参数只有车轮前束和外倾角两种。
Once drilled, check the arm in the steering stem to insure that the two bolts holes can be installed.
一旦钻，检查转向臂的茎确保这两个螺栓孔，可以安装。
So an accurate and useful method is provided for designing the splitAckerrman steering linkage of double arm suspension .
为双横臂式悬架转向梯形设计提供了精确实用的方法。
Macro and micro structure of the fractured steering knuckle arm was examined by optical microscope and scanning electron microscope.
采用光学显微镜和扫描电镜对断裂转向节臂的宏、微观组织进行了分析。
That respectively does the academic calculation and ADAMS simulation for steering trapezium and pitman arm mechanism, and optimizes the steering characteristics.
分别就转向梯形机构和转向摇臂机构进行了理论计算和ADAMS仿真，并对转向特性进行了优化。
The paper aims at the problems of steering linkage with transition pitman arm of a bus, uses system dynamics software ADAMS to check and find out the problems, and then improves the design.
针对某款客车带有转向中间臂的转向杆系出现的问题，利用系统动力学分析软件ADAMS进行分析，找出问题并进行设计改进。
The hole of the auxiliary hanging rope connecting plate of the upper arm of the hoist is connected with an auxiliary steel cable chain hanging rope and a small steering rope.
吊具上臂的副吊系连接板的孔内连接副钢丝绳链条吊系和转向小绳。
The four-bar linkage included in the mechanical steering system of industrial vehicles is composed of the crank of steering gear, longitudinal connecting rod, the arm on kin pin and frame.
在轮式工业车辆的机械式转向操纵系统中，联系转向器与梯形机构的纵拉杆机构，在构造上属于含有两个球铰和两个圆柱铰的RSSR机构。
The steering-knuckle ARM, attached to the front wheels, are therefore forced to swing the wheels to the right or left on their pivots.
于是，与前轮相连的转向节臂使车轮在其轴线上左右转动。
The steering-knuckle ARM, attached to the front wheels, are therefore forced to swing the wheels to the right or left on their pivots.
于是，与前轮相连的转向节臂使车轮在其轴线上左右转动。
应用推荐