Only new or rewound stators may be used as a finished good.
只有新的或重新缠绕的定子可以作为完好产品。
The efficiency of the stage with four different stators is presented.
研究表明本文采用的弯导叶方案没有提高级效率。
Depending on the characteristics of products used and on the type of stators and rotors.
根据产品使用特点及定子和转子的类型确定流量。
The results show that the curved stators used in this paper are not to improve the stage efficiency.
研究表明本文采用的弯导叶方案没有提高级效率。
Simulation of 3D flow in a repeated low speed compressor about the effects of bowed stators on flow performance was presented in this paper.
本文采用全三维粘性数值模拟方法研究了重复级低速压气机不同静叶弯角对流动特性的影响。
Hard disk rotors suspended by active magnetic bearings consists of stators, rotors, magnetic actuators, sensors, controllers and power amplifiers.
磁悬浮硬盘转子系统由定子、转子、电磁作动器、传感器、控制器和放大器等部件组成。
A calculating method on each power losses and stators voltage and current of asynchronous motors is given, which is operated in reducing stator losses voltage.
给出了一种计算异步电动机降压运行时各损耗功率及定子电流电压的方法。
Based on ANSYS - a large finite element analysis software for calculate and analysis platform, a system developed for the design optimization of turbine stators.
本文以大型有限元分析软件ANSYS为计算分析平台，开发了发动机涡轮静子结构优化设计系统。
Servo motors, servo ECO-drives, touchscreen monitors, amplifier cards, modules, prom processors, valves, hydraulic pumps, line filters, rotars, and stators can be found here .
主要是以下产品：伺服电机、ECO伺服驱动器、触摸屏、放大器板卡和电源模块等。
Based on the structure characteristics and operation principle of permanent magnet linear synchronous motors (PMLSM) with discontinuous stators, a simulation model was developed.
从不连续定子永磁直线同步电动机的结构特点和工作原理出发，建立起电机的仿真模型。
The numerical simulation of three dimensional flows in a steam turbine stage with four different curved stators is completed using commercially available CFD code NUMECA in this paper.
在四种不同弯曲静叶方案下利用CFD流场计算软件NUMECA对某汽轮机弯曲叶片级的内部三维流场进行了数值模拟。
This paper analyzes the causes of overfire for stators and rotors of mining cage motors and points out the measures of preventing the overfire for motors in design, manufacture and use.
分析矿用鼠笼型电机定子、转子烧损的原因，提出设计、制造及其使用中预防电机烧损的措施。
The characteristics of the flow and the variation of the parameters are analyzed according to the numerical solvers. The efficiency of the stage with four different stators is presented.
根据数值研究结果分析了不同弯静叶方案下级内流动特性、气流参数的变化，给出了四种静叶方案的级效率。
The processing accuracy of the component, the fit-up gaps of the moving parts, the requirements of gas tightness detection, and the fit-up technology of the rotors and stators were proposed.
提出了机件加工精度、运动部件配合间隙及阀组气密性检测要求以及电机定转子装配工艺要求。
But it is not suit for precision dies, such as the folding and riveting die for the stators and rotators of motors. For precision dies, the method of bonding the guide bushes with glue is applicable.
但此方法用于精密模具(如电机定转子叠铆模)则有一定的弊端，用胶水粘接导套的方法可适用于精密模具。
But it is not suit for precision dies, such as the folding and riveting die for the stators and rotators of motors. For precision dies, the method of bonding the guide bushes with glue is applicable.
但此方法用于精密模具(如电机定转子叠铆模)则有一定的弊端，用胶水粘接导套的方法可适用于精密模具。
应用推荐