The conversion of nylon chips into fiber comprises two distinct processes: spinning and drawing.
从尼龙切片到纤维的转化包括两个不同的过程：纺丝和牵伸。
Shine and flat polyester staple fiber was produced by using profiled spinneret and special spinning and drawing process.
通过异形喷丝板的设计及特殊纺丝和后拉伸工艺生产了闪光扁平涤纶短纤维。
A kind of high strength and high modulus fiber was prepared by melt spinning and drawing of high molecular weight polyethylene (HMWPE) plasticized by wax.
采用石蜡增塑高相对分子质量PE后纺丝并经高倍拉伸制备高强高模纤维。
The prepared Type HT-6 high tenacity polyester fiber finish is proved to be satisfactory to the process of spinning and drawing of high tenacity polyester fiber in practice.
研制成的HT - 6型高强涤纶纺丝油剂，经应用证实能满足高强涤纶纤维纺丝和拉伸工艺的要求。
Properties and treatment of the luminous pigment, modified PP and the process conditions such as spinning temperature, drawing, heating setting were investigated.
并对生产所需的发光颜料性能及处理方法、聚丙烯改性和纺丝温度、拉伸、热定型等生产工艺进行了探讨。
The fairly good structure of PGA fiber can be obtained at low spinning velocity and high after-drawing ratio.
采用低速纺丝高倍后拉伸的工艺路线可以得到具有较好结构的PGA纤维。
By measuring spinning technology and drawing condition of the copolyester, suitable spinning conditions were obtained. And effects of drawing condition on properties of the fibers were discussed.
又对该共聚酯的纺丝工艺和拉伸条件进行试验，得到了合适的纺丝和拉伸工艺，讨论了拉伸条件对纤维性能的影响。
The effects of spinning temperature, spinning pressure and drawing velocity on the degree of profile and effective diameter of the fibers were studied and the preparation technology was determined.
研究了纺丝温度、压力、牵伸速度对纤维异形度和当量直径的影响，确立了异型截面碳化硅纤维的制备工艺。
Spinning is the process of drawing out and twisting a mass of cleaned prepared fibres. filament yarns generally require less twist than do staple yarns.
纺纱是对纤维集合体牵伸加捻的过程。长丝比短纤维需要的捻度少。
Property of cuprammonium rayon was introduced. Three passages drawing was done, and this processing plan was adopted when spinning cuprammonium rayon cotton blended knitting yarn.
介绍了铜氨纤维的特性，铜氨纤维与棉纤维混和纺制针织用纱的工艺方案是采用三道并条的工艺。
The forming technology of rear shock absorber cap is analyzed, and its drawing die, flanging die and spinning die structure are also introduced.
分析了后减震器帽的成形工艺，介绍了成形该零件的拉深模、翻边模以及旋压模具结构。
Spinning is the process of drawing out and twisting a mass of cleaned, prepared fibres. Filament yarns generally require less twist than do staple yarns.
纺纱是对纤维集合体牵伸加捻的过程。长丝比短纤维需要的捻度少。
The result showed that the spinning performance, drawing property and thermal property all decreased with the increase of magnetic particle content.
结果表明：随着磁粉含量的增加，磁性纤维的纺丝性能、拉伸性能、热性能下降。
Present situation and problems of spinning line heating and drawing technology in China were described. Comparison with other high speed spinning technology was made.
介绍了国内纺程加热拉伸技术的现状、技术特点和存在的问题，与其它几种高速纺技术进行了对比，并对这项技术的开发提出了合理性建议。
The PTT DT fiber was produced by POY spinning line and modified parallel drawing equipment.
采用POY-DT生产工艺路线，在POY纺丝线和经改造的平衡拉伸机设备上生产出PTT长丝。
Ultrahigh molecular weight polyethylene ( UHMWPE) fiber was prepared by gel spinning and ultra-drawing technology.
采用冻胶纺丝-超拉伸技术纺制了超高相对分子质量聚乙烯（UHMWPE）纤维。
PDLLA/HA composite fibers were produced by melt spinning, and the choices of the process parameters such as temperature, revolving speed and drawing speed etc were discussed.
选用熔融纺丝法制备PDLLA／HA复合纤维，探索了熔融纺丝过程中温度、挤出机转速、拉伸速率、加料速度和冷却速率等一系列工艺参数的选择及其影响因素。
The slenderizing wool fiber and the drawing expansion wool fiber is spanned with normal wool, mercerization wool, cashmere, we can decrease the cost and increase spinning functions.
拉伸细化羊毛纤维和拉伸膨化羊毛纤维通过与普通羊毛、丝光毛、羊绒等的混纺降低了原料成本、增加了可纺性。
This paper introduces the on-line detection system of spinning processing and its application in picking, carding and drawing.
介绍了在线检测系统的构成和在线检测技术在清花、梳棉、并条等工序中的应用情况。
High shrinkage polyester staple was prepared by using amorphous polyester chip. The technology of drying, spinning, drawing and non-setting was studied.
采用非结晶聚酯切片制备高收缩涤纶短纤维，对切片干燥、纺丝、拉伸、定型等工艺进行了研究。
The bright profiled PET can be produced by the forming technology extruded from the spinneret slit and high-speed spinning-drawing with bright polyester chips.
介绍了以超有光聚酯切片为原料，采用熔体狭缝挤出成型技术和高速纺丝牵伸一步法工艺制取异形pet纤维的生产方法。
The effects of T30S and Z30S chips, spinning process and drawing process on yarn irregularity of coarse denier PP filament were analyzed.
分析了T30S，Z30S两种切片及其纺丝拉伸等工艺对粗旦丙纶长丝不匀率的影响。
Ultrahigh molecular weight polyethylene fibers(UHMWPE) of different gel concentration were prepared using gel spinning process followed by solvent extraction, drying and drawing.
采用凝胶纺丝工艺制备了具有不同质量分数的超高分子质量聚乙烯凝胶纤维，并对其进行了萃取干燥和后拉伸等处理。
The differences on drying, spinning, winding and parallel drawing between PTT fiber and PET fiber were pointed out. The production process of PTT DT was discussed.
着重指出了ptt纤维生产在干燥、纺丝、卷绕、平行拉伸上和PET纤维的不同，并结合实例对POY—DT工艺的要求作了探讨。
Spinning is the process of drawing out and twisting a mass of cleaned, prepared fibres.
纺纱是对纤维集合体牵伸加捻的过程。
Spinning is the process of drawing out and twisting a mass of cleaned, prepared fibres.
纺纱是对纤维集合体牵伸加捻的过程。
应用推荐