The paper introduces one kind of pollution source data acquisition system design based on LP3500.
本文介绍了一种基于LP3500的污染源数据采集系统的设计。
Three component data acquisition with compressional wave source was applied to YC area for predicting fracture reservoir characters.
为了探测yc地区裂隙型储层特征，在该区进行了纵波源三分量数据采集。
Uses multimedia through the USB connection carries on the data acquisition the source program, through debugging.
USB接口利用多媒体进行数据采集的源程序，通过调试的。
It also favours eliminating the negative influence caused by source errors such as source strength error, source orientation error and so on in seismic data acquisition.
它同时还可以消除数据采集时由于震源的误差(如震源强度误差、震源取向误差等)所带来的影响。
The system is composed of rotate drive and control unit, data acquisition unit, program control load, initial excitation source and measure-control program.
本文设计的发电机检测系统由转速驱动和控制单元，数据采集单元，可程控的负载，初始励磁电源以及应用测试软件组成。
Data record unit complete data acquisition, which records analog quantity data, parallel and serial digital data, parallel and serial graphic data from the signal source to CF card.
数据记录单元完成数据采集，把信号源发送的模拟量数据、并行和串行数字量数据、并行和串行图形数据记录到存储设备的CF卡上。
Source condition is one of important factors in data acquisition of high-resolution seismic exploration.
震源激发是高分辨率地震勘探野外数据采集的重要环节之一。
Due to time effectiveness for water regime information transmission, acquisition of source data to final calculated results should be accomplished during a given period of time.
水情信息传递的时效性，要求从原始数据采集到最终计算结果的取得，须在有限的时间内完成。
Noise can be minimized by using source and receiver arrays, generating minimal noise during acquisition and by filtering and stacking data during processing.
采集时可以用震源及检波器的组合，使噪声达到最小；在处理时，可以用滤波和数据叠加使噪声最小。
The acquisition or interpretation of data from a storage device, from a data medium, or from another source.
从存储设备、据媒体或其它数据流中获得或解释数据。
This method can enhance the signal transfers distance, precision and offer the trustiness signal source to picture data acquisition system.
提高了信号的传输距离和精度，为图像数据采集装置的测试提供了可靠的信号源。
A data acquisition system with the MCS-51 single-chip microcomputer control and a software for dynamic behavior detection of arc welding power source is described in this paper.
本文介绍了一种由MCS - 51系列单片机构成的数据采集系统以及用于电焊机动特性的测试软件。
In this paper, by combining artificial intelligence with data base technology a knowledge-acquisition method by taking the data of MIS(Management Information System)as the knowledge source is derived.
本文从工人智能与数据库技术结合的角度出发，提出一种以管理信息系统（MIS）的数据为知识源的知识获取方法。
The system mainly consists of wide-band light source, fiber Bragg grating, unbalanced Mach-Zehnder interferometer, and data acquisition and processing components.
系统主要由宽带光源、光纤光栅、非平衡马赫-曾德干涉仪、数据采集与处理等部分组成。
This paper provides the real method for data acquisition subsystem programme in the large scale information management system and gives some critical source codes.
介绍了大型信息管理系统中数据采集子系统的实现方法，还给出了一些关键部分源代码。
Due to the weakness and randomness of natural source in magnetotelluric method, a great deal of effort is spent in the field records and data acquisition.
大地电磁法由于天然场源信号的微弱性和随机性，在野外记录和数据采集方面需要花费巨大的努力。
The hardware design includes electrical source design, measuring controlled circuit design, data acquisition section design, checking-at-zero circuit design and so on.
硬件设计包括测试电源、测试控制电路、数据采集部分、过零触发电路等。
According to the source of error, for effective elimination of the error count data acquisition by use the SCM procedures, further improve the measurement accuracy.
根据误差源分析，在单片机程序处理中，有效将数据采集计数误差消除，进一步提高了测量精度。
Seismic dynamite source is one of the key techniques in seismic data acquisition.
震源是地震勘探野外数据采集中的一个关键技术问题。
FPGA is used as trigger source. The data acquisition of precise timing has been realized with edge-trigger manner. Meanwhile, the data analysis is also realized in the system.
系统采用FPGA作为数据采集触发信号源，实现了精确定时的数据采集，同时对采集的数据进行分析和处理。
Data Acquisition is the set of processes that capture, integrate, trans-form, cleanse, reengineer and load source data into the data warehouse and operational data store.
数据获取是获取，集成，转换，清洗，重构和数据加载到数据仓库和ODS系统的一系列的过程。
Data Acquisition is the set of processes that capture, integrate, trans-form, cleanse, reengineer and load source data into the data warehouse and operational data store.
数据获取是获取，集成，转换，清洗，重构和数据加载到数据仓库和ODS系统的一系列的过程。
应用推荐