It is valuable for CFB desulfurizer design optimization to study the gas-solid flow field characteristic in CFB riser.
研究流化床提升管内气固流场分布情况对设计和优化循环流化床脱硫器有着重要价值。
The gas-solid flow in pipe and venturi meter is discussed in this paper on the basis of fundamentals of two-phase flow.
本文从两相流的基本原理出发，分析等截面、变截面和文丘利流量计内的气—固两相流动。
Firstly, the pressure distribution of gas solid flow along the circulating route is analyzed and experimentally studied.
分析气固两相流在循环路径中的压力分布，并通过试验对其进行了研究。
Cell model is employed to set up the mass balance of 8 gas components, solid flow, carbon flow and total energy balance.
建模采用“小室模型”方法，将气化炉分为多段，分别建立8种气体成分、固体和碳质量平衡以及总体能量平衡。
It is valuable for CFB desulfurization reactor design optimization to study the gas-solid flow field characteristic in CFB riser.
研究流化床提升管内气固流场分布情况对设计和优化循环流化床脱硫器有重要意义。
DEM (Discrete Element Method) is used to simulate the gas-solid flow of a two-dimension fluidized bed with L-type wind caps in this paper.
该文采用离散元素法DEM模型对二维L型定向风帽流化床中的气-固流动特性进行模拟。
An artificial neural network model was set up to simulate the hydrodynamics of the gas-solid flow in the gas-solid circulating fluidized bed.
提出了气固循环流化床中气固流动的人工神经网络模型。
The formula for calculating the solid flow rate in gas-solid flow oy using venturi meter is presented, which is also linear under certain conditions.
最后得出气—固两相流中，用文丘利流量计测量固相流率时的计算公式。它在一定条件下也是线性的。
The main object is to study three-dimensional physical character of gas-solid flow past a circular cylinder by using direct numerical simulation method.
本文首先采用直接数值模拟方法研究了三维气固两相绕圆柱的物理特征。
The experimental study of a gas solid flow pattern and gas diffusion characteristics using polystyol particles and glass bead has been carried out in a pressurized spouted fluidized bed.
在一个加压喷动流化床装置上进行了冷态实验，研究加压条件下床中的气固流动状态和气体在各部分的扩散特性。
The interaction between gas and particles under different flow regimes, ranging from minimum fluidization to pneumatic transportation, was investigated in a vertical gas-solid flow system.
本文对垂直气固两相流动系统中，从初始流态化到气力输送的整个区域内气固两相之间的相互作用规律进行了研究。
The influence of the arrangements of pipes on gas solid flow characteristics in the dense section of standpipe in the circulating fluidized bed is studied on a cold state experiment platform.
在冷态试验台上研究了循环流化床料腿密相段中不同管束布置方式对气固流动特性的影响。
On the basis of previous explicit algorithms realized by the authors, a new vectorial and explicit algorithm is proposed and developed for solid flow model under the frame of Eulerian description.
基于笔者在欧拉描述下模拟注射填充过程的显式算法，应用实体流模型实现了用于注塑填充过程的全矢量化运算显式算法。
The computational fluid dynamics software FLUENT is used to simulate the 3-d two-phase (gas-solid) flow of cyclone separator.
应用计算流体力学软件FLUENT对旋风分离器进行三维气固两相流场的数值模拟。
The computational fluid dynamics software FLUENT is used to simulate the 3-d two-phase (gas-solid) flow of cyclone separator.
应用计算流体力学软件FLUENT对旋风分离器进行三维气固两相流场的数值模拟。
应用推荐