The experimental results on commercial pure titanium verify the obvious changes in the microstructure, hardness and wear resistance after laser solid diffusion treatment.
对工业纯钛的初步试验结果表明，用激光进行固态扩散渗氧处理可以明显改变钛表层组织、硬度和耐磨性。
When the reaction products form as high melting point CA2, CA6 and MA spinel in a continuous solid phase it will clog the liquid channel and resist the further diffusion of fused slag in the brick.
并且当熔渣与耐火材料的反应产物为高熔点的CA2、CA6和MA尖晶石相且连续交错分布时，能堵塞液相扩散通道，抑制熔渣向耐火材料内部的进一步渗透。
The experimental study of a gas solid flow pattern and gas diffusion characteristics using polystyol particles and glass bead has been carried out in a pressurized spouted fluidized bed.
在一个加压喷动流化床装置上进行了冷态实验，研究加压条件下床中的气固流动状态和气体在各部分的扩散特性。
The technique of solid -electrolyte - potentiometry (SEP) was used to investigate the effect of internal diffusion.
采用固体电解质电位测定技术进行了内扩散影响的考察。
Metal solid transformation is simply classified into shear and diffusion type, which would lead to doubt and even confusion.
金属固态相变被简单区分为切变型、扩散型两类，难免引起质疑甚至混乱。
Methods Monostearin solid lipid nanoparticles was prepared by solvent diffusion method in aqueous system.
方法用水性溶剂扩散法，制备得到甘油单硬脂酸酯固体脂质纳米粒。
Solute diffusion inside a capillary was used to simulate the mass transfer process inside a solid for a liquid solid system.
以封闭于毛细管内的溶质扩散模拟固液分离体系中深层溶质扩散过程。
Such diffusion process is often affected by the mechanical stresses in the solid.
通常这样的扩散过程是受到固体里面内应力的影响。
The dissolution was confirmed to be a quasi-reversible process, which was controlled by solid-state diffusion and charge transfer.
证明针镍矿的阳极溶解是由固相内扩散传质和电荷传递步骤混合控制的准可逆电极过程；
Crystals in an unsaturated solution dissolve, with subsequent diffusion away from the solid-liquid interface.
当晶体溶解在不饱和溶液中时，分子就会在固液界面处产生相应的扩散。
The variation of the carbon diffusion coefficient at the vicinity of the phase boundary during the process of eutectic solid state phase transformation of the phase boundary was analyzed.
然后分析了碳钢在过冷等温时，相界面共格的固态相变过程中，相界面附近碳的扩散系数变化的情况；
The preparing method comprises brushing material, solid-phase composition, diffusion annealing and cold rolling.
其制造方法包括刷料、固相复合、扩散退火、和冷轧工艺步 骤。
Cycling life tests investigated that the capacity of alloy prepared by ball milling decreased to 40% after 50 cycles, while the solid-state diffusion method just 25 cycles.
循环寿命测试，球磨的样品经过50次循环其容量衰减到40%，非球磨样品经25次的循环即衰减到同样程度。
The results show that the mother sheet and the grown layer are bonded by diffusion forming a solid solution.
试验结果表明，母带和凝固层靠相互扩散形成固溶体而实现良好的冶金结合。
With the increasing of the viscosity of electrolyte, the diffusion coefficient of I_3 ion decreased rapidly to be a new controlling step in the quasi-solid state dye-sensitized solar cell.
发现随着电解质体系粘度的增加，I_3~-离子扩散系数急剧下降，进而在准固念染料敏化太阳能电池的光电转换过程中形成新的速控步骤I_3~-离子的扩散过程。
With the increasing of the viscosity of electrolyte, the diffusion coefficient of I_3 ion decreased rapidly to be a new controlling step in the quasi-solid state dye-sensitized solar cell.
发现随着电解质体系粘度的增加，I_3~-离子扩散系数急剧下降，进而在准固念染料敏化太阳能电池的光电转换过程中形成新的速控步骤I_3~-离子的扩散过程。
应用推荐