Analysis and comment are made on the floating cylinder sleeve method known in late years.
对近几年来发表的浮动缸套测量法进行了分析和评述。
Cleaning oil and gas well, pipeline, sleeve, stratum and equipment composition and its using method.
清洗油和气井,管道,套管,地层和设备的组合物及其使用方法。
The concrete measure and method of preburied sleeve installation and grouting construction are addressed in this paper.
文章介绍了该压缩机基础预埋套管安装及灌浆施工的具体措施和方法。
A simple testing method of wear resistance for piston ring and cylinder sleeve is introduced.
本文介绍一种简易的活塞环与气缸套磨损试验方法。
A kind of measuring method and corresponding measuring instrument for measuring cone shaft and cone sleeve of the high-speed wire rolling mill's roller are introduced.
介绍了一种检测高速线材轧机轧辊锥轴与锥套锥度的检测方法以及相应的锥体锥度检测仪。
A novel method is proposed for analyzing the sleeve monopole at the center of a circular ground plane.
提出了一种分析有限尺寸圆盘地面上套筒单极子天线的新方法。
The calculation of the interference of the cover and sleeve is as follows:secondary calculation and additional rigidity method.
计算链板和套筒的过盈应力的方法有:二次计算法和附加刚度法;
Taking the sleeve roller chain as an object the influencing factors on dynamics were analyzed and the dynamic modeling method for this kind of system was discussed.
以套筒滚子链为工作执行机构的一类机械系统为研究对象,分析了其动力学影响因素,探讨了该类系统的动力学建模方法。
The advantage for manufacturing the roll sleeve forging with ESR ingot is described in this article, and the upgrading method for the original process has been set forth.
讨论了电渣重熔钢锭在生产辊套锻件时的优势,提出了对原工艺的改进方法。
By analysis and comparison between the two methods, some shortcomings of plate pressure connection method are shown and the connection method of sleeve structure is recommended.
本文通过对这两种压接线方式的比较分析,指出板式压接线方法的一些弊端,并推荐选择筒式结构的接线方法。
The invention relates to a special butt joint sleeve for a large breakage anchor bolt and the butt joint method thereof.
本发明涉及一种大型破损地脚螺栓对接专用套筒及其对接方法。
The sleeve monopole antennas at an arbitrary conducting ground plane are analyzed by the method of moment (MoM).
利用矩量法分析任意形状导体地面上的套筒单极子天线。
Taking a curve sleeve as an example, the principle and method to test non-substance curve are related. At the same time, the errors are analysed, giving the way improved.
本文以曲线套筒为例,论述了非实体曲线测量原理和方法,并对其误差进行了分析,提出了改进方法。
A sleeve antenna mounted on metallic cylinder is analyzed by moment method.
采用矩量法分析了安装在金属圆柱筒上的套筒天线。
On the base of finite element method about contact problem, building models of the flanged connection and the sleeve connection of aircraft is introduced.
在接触问题有限元法的基础上,介绍飞行器的盘式连接、径向螺钉套接接触模型的建立。
Calculation method and optimum design is presented for the computation of kinematics for suspension system with abnormal rubber sleeve.
通过研究,提出了一种精确计算异形橡胶衬套的悬架系统动力学方法与优化设计方法。
A new moment method is presented to analyze sleeve monopole antennas at the center ofa circular ground plane.
研究了一种快速精确计算有限尺寸圆形导体地面上套筒单极子天线的新方法。
Conclusion:The small gap sleeve bridging might become a effective method to increase growth rate of nerve.
结论:小间隙套接法有可能成为解决神经断端定位难及提高神经再生效果的有效手段。
Used the maximum strain-energy theory and strength limit analytic method to check the important part such as sleeve, end-plate, etc.
运用最大应变能理论和强度极限分析法,对简体、端板等重要部件进行了强度校核。
In this paper, the method of moments is used to compute sleeve monopole antennas.
本文利用矩量法分析计算套筒天线。
The technological treatment , application scope and the selection method of the heat shrinkable sleeve for marine use are described in detail.
该文简述了热缩套管选用、施工处理等内容,并介绍了热缩套管工艺在舰船电缆密封方面的应用。
Taking for example the wear of connecting rod copper sleeve, the paper introduces the application of this method to the prediction of internal combustion engine maintenance and fault detection.
文中以内燃机连杆钢套磨损为例,介绍了其在内燃机维修状态预测和故障珍断上的应用。
The principle of this method was discussed, an effective method was found for controlling the distortion of a sleeve fork like produce after high frequency induction hardening.
进行了套管叉高频淬火工艺试验,解决了该零件的淬火畸变问题。
The method and the device enable the materials to be dried to move to and fro from the drying roller to the sleeve, prolong the time of the material in the drying device and fully dry the material.
本发明使待烘干的物料经烘干滚筒至套筒往返移动,延长物料在烘干装置的时间,使物料得到充分干燥。
The conclusion can be used to provide direction for the choice of composite sleeve material, the design of built-up method and the roll structure.
可用于指导复合轧辊材质选择、热装方法的制定和轧辊结构设计。
A calculating method to determine mill sleeve length is presented and the optimizing principle is introduced combined with practice.
对套铣筒的长度选择研究了一个计算方法,并结合实际情况提出了优选原则。
The method of 5-ring screw hoop, 1-pen hoop and non-shrinkage high-strength mortar poured into sleeve is used at the seismic joint of new-type prefabricated reinforced concrete beam-column.
新型预制钢筋混凝土梁柱抗震节点采用五环螺旋箍、一笔箍和在套筒中灌注无收缩高强砂浆的方法制作。
After 6 months of test-operation, the method has been proven satisfactory that the problem of scale formation is solved and the design capacity of sleeve kiln is ensured.
通过半年的工业性生产试验,解决了这一问题,保证了生产顺行,使其达到了生产设计指标。
After 6 months of test-operation, the method has been proven satisfactory that the problem of scale formation is solved and the design capacity of sleeve kiln is ensured.
通过半年的工业性生产试验,解决了这一问题,保证了生产顺行,使其达到了生产设计指标。
应用推荐