The master-slave mode improves the expandability.
主从模式增强了系统的可扩展性。
A master slave mode of CNC system with a half closed loop control in the numerical control transformation of a machine tool was designed and implemented.
介绍了一个半闭环主从式数控系统在普通机床数控化改造中的设计及实现。
This paper briefly introduced the feature of PCI protocol slave mode interface chip PCI9052 and illustrated the advertent items when configuring the EEPROM.
本文简要介绍了PCI协议从模式接口芯片pci9052特点，并说明了EEPROM配置注意事项。
The system, which consists of one body module and a number of extension modules, achieves one point-to-multipoint data transmission based on master-slave mode.
系统由一个PL C本体模块和多个PLC扩展模块组成，实现了主从模式的一点对多点的数据传输。
After researching the defects of RS485 in master-slave mode, control network of equivalent mode in multiple computer's communication is put forward in this paper.
我们分析了RS - 485主从式多机通信的缺点，提出了对等式多机通信网络控制。
The interface can be used in embedded system which need fast switch between USB host mode and slave mode. And it can be communicated with U disk in host mode and PC in slave mode.
最终实现了嵌入式系统USB主从模式的快速切换以及在主机模式下与U盘、从机模式下与PC机的通信。
Secondly, Single-Chip computer system soft design under host and slave mode of CH375 is introduced, and the paper shows the flow chart, the program design in detail and some codes.
其次，介绍了CH375主从模式下单片机系统软件设计，并给出了部分源代码和程序流程图；
etc/bluetooth/hcid.conf: HCI daemon configuration file used by hcid that specifies link mode (master or slave), link policy, inquiry and scan mode, and so on
etc/bluetooth/hcid.conf：hcid所用的HCI后台进程配置文件，它指定了链接模式（主或从）、链接策略、询问和扫描模式，等等。
Load the bonding module with adaptive load balancing (mode 6) and up-delay (milliseconds to wait after link recovery before enabling a slave): modprobe bonding mode=6 updelay=200.
用适应性负载平衡模式（mode6）和up-delay 参数（链路恢复之后到启用从进程之前等待的毫秒数）装载绑定模块：modprobebonding mode=6updelay=200。
The slave application must of course meet a lot of requirements that allow it to run in embedded mode.
仆应用程序当然需要达到很多要求才能在嵌入模式中运行。
It is shown by theory and case study that the master - slave clock mode in a com munication system is ideal for proper functions of the current differential protection.
理论及实例分析表明，通信系统的主—从时钟方式是电流差动保护装置在复用数字通信系统时正确工作的理想方式。
The communication between host and slave is realized through polling mode.
主控机通过轮询方式与各从机通信。
In the design of column readout stage, master and slaver structure has been adapted, where master amplifier converts charge to voltage, and slave amplifier works with standby mode to drive output bus.
列读出级采用新型主从两级放大列读出结构，其中主放大器完成电荷到电压的转换，从放大器驱动输出总线来满足一定的读出速度。
After deeply analyzing sniff mode which is a low power operation mode of bluetooth, a learning function is proposed to approximate the distribution of the incoming traffic at a master-slave pair.
在深入分析蓝牙的低功耗工作模式一呼吸模式基础上，提出用学习函数来近似估计主从对之间通信流分布。
This paper discusses the method of software development of measurement and control platform for automobile component test based on host-slave computer mode.
②基于上述框架模型和测控平台的功能需求，划分功能模块，并设计开发出测控平台软件系统的功能类库组件；
This paper discusses the method of software development of measurement and control platform for automobile component test based on host-slave computer mode.
②基于上述框架模型和测控平台的功能需求，划分功能模块，并设计开发出测控平台软件系统的功能类库组件；
应用推荐