They are fit for such parts as ladle bottom, wall and slag line.
适用于钢包包底、包壁、渣线等部件。
The brick gained favorable application result in the ladle slag line.
生产的不烧砖在平炉钢包渣线上使用，取得了较好效果。
Based on analysis of the forming causes of slag line dripping water, a solution plan was put forward.
通过对渣线淋漓水成因的分析，提出解决方案。
Inclusions in the gray strip defects consist of MgO and trace melilite, which result from MgO-C refractory in slag line.
灰色条带状缺陷中外来物主要为氧化镁，并含少量黄长石，来源于渣线镁碳砖耐火材料；
The approach of reutilization of by-product salt slag of hydrazine hydrate was studied. Process technology line was ensured, and technology economic estimation was discussed.
研究了水合肼副产盐渣的回收利用途径，确定了工艺技术路线，讨论了技术经济评价。
Recycling waste tin material: lead-free solder recovery and recycling, tin tin slag the recycling, tin line recovery, solder paste recycling waste tin tin ash, such as waste lead recovery.
回收废锡料：无铅焊锡回收、锡渣回收、锡条回收、锡线回收、锡膏回收、锡灰等废锡废铅回收。
Slag manipulator control system can communicate with PC control system and can ensure the automatic casting production line work under the control of the production process.
除渣机械手控制系统能够和上位机控制系统进行通信，从而保证整个自动浇注生产线在预定的生产流程控制下进行生产。
The experimental results show that this method is feasible on principle, and has directive meaning for realization of on-line measurement of the height of foaming slag on site.
在实验室进行了模拟检测实验结果表明，该检测方法在原理上是可行的，对于在现场实现熔渣泡沫高度的在线检测具有指导意义。
This paper describes a computer visual technique for on-line measurement of the height of foaming slag in blast furnace which simulation experiment has been done in laboratory.
给出一种基于计算机视觉技术的高炉熔渣泡沫高度在线检测方法。
Through carrying out fractional filtration, depositing and using the waste heat of washing blast furnace slag water, the heating and district heating line system is set up.
将高炉冲渣水进行分级过滤、沉淀，利用冲渣水的余热，建立了高炉冲渣水余热供暖供热系统。
Before installation on the suction and discharge line to clean, remove rust and dirt, especially welding pipe welding slag must be thoroughly cleared, to avoid killed after entering the pump.
安装前对吸入、排出管路要清理干净，去掉铁锈等脏物，特别是焊接管路的焊渣必须彻底清除，以免进入泵后咬死。
By using this process to repair castings, there is no obvious separating line, no slag inclusion and gas hole between the welding zone and base metal.
用此工艺焊补铸件，焊补区域与基体间没有明显的熔合线，无渣孔、气孔等缺陷。
By using this process to repair castings, there is no obvious separating line, no slag inclusion and gas hole between the welding zone and base metal.
用此工艺焊补铸件，焊补区域与基体间没有明显的熔合线，无渣孔、气孔等缺陷。
应用推荐