In the process of completing, the mechanism design requests are considered fully, some methods such as the computer assistant simulation design, finite element analysis and test verify are adopted.
在完成过程中，充分考虑了铺设轮的机械设计要求，采用了计算机辅助仿真设计、有限元分析和试验校验的方法。
By comparing the results obtained from the test and finite element analysis, a very good agreement is found, showing the accuracy and feasibility of the simulation with finite element method.
将有限元模拟结果和试验结果进行了比较，取得了较好的一致，验证了有限元分析的正确性和可行性。
This method takes advantage of the dynamic simulation function of finite element analysis and the thermodynamic theory to calculate the value of thermal flux.
该方法利用动力学分析功能，结合传热学原理求解热流传递数值；
Finite element simulation for upsetting and performing steps has been done by finite software DEFORM on the basis of theoretical analysis for upsetting steps of wheel.
在对车轮镦粗工步进行理论分析的基础上采用有限元软件DEFORM对镦粗及预成形工步进行了有限元模拟。
The simulation method of the rigid-elastic coupling control system is introduced by using the interaction of the finite element analysis software and the control system simulation software.
该文介绍了交互使用有限元分析软件和控制系统仿真软件实现具有刚柔耦合结构复杂系统的仿真方法。
This paper simulates the temperature field associated with laser surface quenching using ANSYS - a finite element analysis software, and a series of studies are carried out based on this simulation.
本文结合先进的大型有限元分析软件ANSYS，对激光表面淬火的温度场进行有限元模拟，并在此基础上，对此展开一系列研究。
The result uniformity of theory and test illustrates the simulation analysis method with finite element can be used to evaluate the reinforcement effect of bridge well and truly.
理论分析与荷载试验结果的一致性表明采用有限元仿真分析方法能够对桥梁加固效果进行准确的评价。
The efficiency and viewing effect of finite element analysis can be improved by means of the visualization of numerical simulation results.
对有限元数值模拟结果进行可视化处理，可提高数值模拟结果检查、分析的效率和直观性。
Through the researches on kind of cylindrical piezoelectric thin film micromotor mechanisms, finite element simulation and modal analysis are carried out in this paper.
通过对柱状薄膜型压电微电机致动机理的研究，运用有限元模拟进行模态分析。
The simulated ultimate load formula and double-control design method of slender eccentrically compressed reinforced concrete member were proposed by nonlinear finite element simulation analysis.
并通过非线性有限元模拟分析，给出了细长钢筋混凝土压杆的极限承载力表达式以及由此确定的双控设计法。
The contrastive analysis of modal test and simulation computation show that the finite element model of body-in-white has well represented the vibration characteristics of the original structure.
模态试验和仿真计算的对比分析结果表明，所建立的白车身有限元模型较好地反映了原结构的振动特性。
The computer simulation procedure is the key to analyzing the mechanical behaviors of the continuous casting segment tower structure using threedimensional finite element analysis method.
应用三维弹性有限元方法对连铸机扇形段框架体进行分析计算的关键在于结构计算机模拟的可能性和可行性。
The finite element analysis software, which was based on the general finite element software package, was developed for numerical simulation of the entire composite cure process.
以通用有限元软件包为基础，开发了能够模拟复合材料整个制造过程中复杂物理化学变化的软件。
This paper deals with the numerical simulation analysis of hot extrusion forming process of the Hooke's Joint using three-dimensional elastoplastic finite element method.
采用三维弹塑性有限元法对虎克式万向节热挤压成形过程进行了数值模拟分析。
The method of Virtual Prototype Building and Finite Element Analysis is theoretically meaning and practically valuable for design and performance simulation of complex mechanical system.
其中的虚拟样机建造方法与有限元分析手段在共同建立的联调平台下解决复杂机械系统设计及性能仿真方面具有理论意义与实用价值。
The simulation results show that the results of finite element analysis agree well with that by measured in field practice.
模拟结果表明有限元分析计算结果与现场实际测量结果吻合度很高。
Finally, simulation and analysis were carried out on the tensile performance of the specimens using finite element methods. The simulated results are in good agreement with experimental values.
最后，利用有限元方法对试件的拉伸力学行为进行了模拟分析，模拟结果与实验值吻合较好。
Therefore, based on rolling bearing implicit finite element solution analysis, using ANSYS/LS-DYNA explicit dynamic module implements, we achieved the rolling contact simulation of motion process.
因此本文在对滚动轴承有限元隐式求解分析的基础上，利用ANSYS/LS-DYNA模块对滚动轴承进行了显式动力学接触分析。
The numerical simulation and analysis of shear resistance behavior of two-side connected steel-plate shear wall (SPSW) was carried out by the finite element software ANSYS.
采用ANSYS有限元程序对两边连接钢板剪力墙进行数值模拟分析。
Let the mechanical dynamics be combined with the method of finite element analysis to establish the simulation method of vibration measurement of dynamics balancing test-bed of mechanism.
将机械动力学与有限元分析方法相结合，建立了机构动平衡实验台振动测量的仿真方法。
The analysis of the simulation value compared with the test results of pipe fittings bended Angle proved the validity of the Finite Element Modeling the tubes bended forming process.
通过对管件弯曲角度的试验结果与模拟值的对比分析，证明了建立管件有限元模型的正确性。
The parametric finite element model of the television with packaging structure was established and its dropping simulation was achieved using the finite element analysis software ANSYS/LS-DYNA.
利用有限元分析软件ANSYS/LS-DYNA，建立长虹电视带包装的参数化有限元模型，对电视裸机与带包装两种工况下的跌落仿真模拟和跌落实验；
The modern tectonic stress field of Shishen 100 area has been found by in situ testing, laboratory core experiment, logging data analysis and 3D finite element numerical simulation.
采用现场测试研究、室内岩心实验、测井资料分析及三维有限元数值模拟技术，获得了史深100地区的现代构造应力场。
Finite element analysis code was used to simulate the effects of laser power and radiation time on the temperature of samples. The simulation results were consistent with the experimental ones.
采用有限元分析软件模拟计算了激光功率和作用时间对清洗过程中温度的影响，计算结果与实验结果规律一致。
An analysis of spinning quality defect on aluminium sheet taper was carried out and studied based on simulation of spinning by finite element method.
针对铝锥旋压成形中出现的质量缺陷，通过有限元分析模拟其成形过程。
The use of large-scale general-purpose finite element analysis software on the short-limb shear wall structural walls were cracking component simulation analysis.
利用大型通用有限元分析软件对短肢剪力墙结构墙肢构件进行了开裂模拟分析。
The use of large-scale general-purpose finite element analysis software on the short-limb shear wall structural walls were cracking component simulation analysis.
利用大型通用有限元分析软件对短肢剪力墙结构墙肢构件进行了开裂模拟分析。
应用推荐