Based on the CARMA model of single input and single output system, a control model of automotive road simulated test in the field of time is deduced and the solution of control data is analyzed.
从单输入单输出系统的CARMA模型出发，推导出以四轮汽车道路模拟试验台为被控系统的控制模型，并对控制量的求解进行了分析。
The test is testified to be reliable and accurate by the description of scaling law of indoor ice pool platform model test, model scale choice, simulated ice conditions, and ice force measure system.
通过对在室内冰池进行的平台冰力模型试验中相似律、模型比尺选择、模拟冰条件以及冰力测量系统论述，证明了该项试验是可靠的和严密的。
The stress state of the circular culvert pipe under soil pressure at rest is analysed with the photoelastic simulated test of the epoxy resin model frozn.
利用环氧树脂模型进行光弹性冻结试验，模拟受填土压力作用时的土坝坝下圆型涵管的受力状态。
The velocity distribution of glass current in the vertical section along the axis of the model has been measured by means of physical simulated test.
采用实体模型试验方法，测试了玻璃池窑模型中心轴纵截面上模拟液的速度分布。
The radial stability of the high capacity transformer winding is compared and re searched with model simulated test. It lays a foundation for development of high capacity products.
对特大容量变压器内绕组径向稳定性进行了模型模拟对比实验和研究，为特大容量产品的开发奠定了基础。
Using the model, noise caused by the two types flow is simulated, compared and analyzed, and there is a good agreement between the theoretical results and test results.
利用这一模型，对两种不同类型的车流噪声进行了模拟计算及对比分析，实测结果与模拟结果吻合较好。
Comparison to the experimental data and simulated data is done to test the effectiveness of the model. Proper velocity model is chosen to better guide the sedimentation tank operation.
通过实际数据与模拟数据的比较，来检验该模型的可靠性，并选择合适的沉降速度模型，以期能够运用该软件可以更好地指导沉淀池的实际运行。
Combining resisting force effect factors time variation model, the static and dynamic test, which is in different situation, is simulated.
结合抗力影响因素时变模型，模拟不同状态下的桥梁静动载试验的过程。
By using model test of simulated materials and finite element calculation and theory deduce, the alternate exterior entry surrounding rock stability in dynamical pressure area is systemically studied.
通过理论推导、相似模拟、数值模拟及现场测试等方法相互结合、相互补充，对动压区外错式巷道的围岩稳定性进行了较为系统的分析研究。
Research work on sensors fault detection and diagnosis method has been studied and deployed. All methods were test in simulated CSTR model. The detection and diagnosis results have been analyzed.
本文主要针对传感器故障检测和诊断方法展开深入研究，并将所研究的方法应用于仿真的CSTR模型，对检测和诊断结果进行分析。
Divided period Stationary Autoregressive model for daily flow of Pingshan hydrological station is established in this paper. Daily flow procedure during 5200 years is simulated to test this model.
建立屏山站日流量分期平稳自回归模型，并模拟了序列长度为5200年的日流量过程对该模型进行检验。
The acoustic analysis model for an automotive exhaust muffler is built, and the transmission loss of exhaust muffler is measured by test and also simulated by using both FEM and BEM.
建立某汽车排气消声器的声学分析模型，采用有限元法和边界元法对排气消声器的传递损失进行了仿真分析和试验测试。
In this paper the open sump flow with vertical intake is simulated with calculation fluid dynamics method according to model-test reports of Lianhu pump station.
本文着眼于使用计算流体力学方法对带有竖直吸水管、正向进水的开敞式前池与进水池的流态进行数值模拟。
Secondly, the whole creep test process was simulated using modified time hardening model of implicit creep equation, the calculated results are fit well to the test ones.
其次，采用隐式蠕变方程中修正的时间硬化模型对蠕变试验全过程进行了仿真，计算结果与试验值能够很好地吻合。
A finite element model for diaphragm air spring is created, and its dynamic characteristics are simulated and verified by test, with both results coinciding each other.
建立膜式空气弹簧的有限元模型，对其动态特性进行仿真和试验验证，仿真结果和试验结果吻合良好。
Finally, the FEA model of the airborne electronic box modified by the results of the modal test needs to be simulated to analyze its structural dynamic characteristics.
实验模态分析已应用于电子产品结构动力学特性方面的研究。
Finally, the FEA model of the airborne electronic box modified by the results of the modal test needs to be simulated to analyze its structural dynamic characteristics.
实验模态分析已应用于电子产品结构动力学特性方面的研究。
应用推荐