Restart xinetd, or send its process a signal to force a reset.
重新启动xinetd，或者向它的进程发送一个重新设置信号。
Finally, reset the signal set.
最后，重置信号设置。
In this mode, the TX signal will be HIGH during reset or idle.
在这种模式下，TX信号为高电平期间将重置或空闲。
Another option is to signal the xinetd daemon to reset.
另一种方法是向xinetd守护进程发送重新设置信号。
To ensure proper operation, the device must be reset after reference signal frequency changes and power-up.
为了确保正确操作，设备必须重置后参考信号频率的变化和电。
Handle reset alarm signal, if there is still in failure, technician on duty must report to project engineer or leader.
手动复位报警信号，如果信号复位还是报故障则向项目工程师或是领导报告。
Pulse counter with manual reset and electric output signal.
有手动复位和电气输出信号的脉冲计数器。
A memory cell and a data line are controlled with a reset signal, so that data can be reliably outputted in the semiconductor device.
存储单元和数据线用复位信号来控制，以使数据可在该半导体器件中被可靠地输出。
Internal reset signal is activated when the timer count value reaches 0 (time-out).
当定时器计数值达到0(超时)，内部复位信号有效。
To create an reset input to the supervisory chip, its input must receive an active-low ground signal, requiring transistor Q1 to turn on.
为管理芯片产生复位输入，其输入必须接收低有效的地信号，需要晶体管q 1导通。
The reading circuit comprises at least one column amplifier (CA), and when the column amplifier is reset, a column amplifier reset signal is generated.
所述读出电路包含至少一行放大器(CA)，当被重置时，即产生行放大器重置信号。
Its function is to provide a latching switch action upon sensing an input threshold voltage, with reset accomplished by an external clock signal.
它的功能是当感应到输入电压界限时提供一个锁存开关，通过外部时钟信号完成复位。
The invention is used for regulating the time for charging the capacitor, further adjusts the maximum duty cycle of the reset signal and improves the output ripple of the buck converter.
本发明用以调节对电容的充电时间，从而调整复位信号的最大占空比，以改善上述降压转换器的输出纹波。
While the internal reset signal is being applied to the CPU, the rate of a refresh signal being generated by a DRAM controller for refreshing data in DRAM is increased.
在将内部复位信号加到CPU的同时，提高由DRAM控制器所生成的用于刷新DRAM中数据的刷新信号的速率。
Then, when the external reset signal is disabled, a delayed reset signal DLYRST is generated and applied to the DRAM controller so that it is reset.
然后，当使外部复位信号无效时，生成一个延迟的复位信号并将其加到DRAM控制器以将其复位。
In most applications, the (manual-reset) pin usually connects to a switch to create a manual-reset signal to the supervisory chip.
在大多数应用中，(手动复位)引脚通常与开关相连，为管理芯片制造手动复位信号。
In addition, any area is reset only when the other areas do not in their scanning and maintaining period, or else the signal in different area produces mutual interference.
另外，任一区域的重置动作则不能与其他区域的扫描、维持动作重复、以避免不同区域间的信号相互干扰。
In addition, any area is reset only when the other areas do not in their scanning and maintaining period, or else the signal in different area produces mutual interference.
另外，任一区域的重置动作则不能与其他区域的扫描、维持动作重复、以避免不同区域间的信号相互干扰。
应用推荐