Twin-wire indirect arc gas shielded welding is a new welding technology.
双丝间接电弧气体保护焊是一种新的焊接方法。
The twin-wire indirect arc gas-shielded welding is a new welding technology.
双丝间接电弧气体保护焊是一种新的焊接工艺。
Special configuration, can satisfy the airway by axial gas shielded welding workpiece and cooling.
专门配置的旁轴气道，能满足气体保护焊和冷却工件的要求。
In this paper, design principle on gun of automatic CO2 gas shielded welding with thick electrode is discussed.
论述了粗丝co2自动焊焊枪的设计原理，并对气流在焊炬中的流动情况和对熔池保护效果作了简要介绍。
Layer can be used to connect steel stamping forming diamond-shaped network, with gas shielded welding spot on the plate.
连接层可用冲压成型的钢质菱形网，用气体保护焊接方法点焊于钢板上。
The range of cleaning (width) shall not be less than 10mm for manual welding, not less than 20mm for gas shielded welding.
清理范围(宽度)对于手工焊不小于10mm，气体保护焊不小于20 mm。
Because of the difference of arc circuit, the welding process of twin-wire indirect arc gas shielded welding is more stable than single wire welding.
由于电弧回路结构不同，双丝间接电弧气体保护焊的焊接过程比单丝焊更加稳定。
And the operation of various gas-shielded welding, ac and DC arc welding machine, stud welding machine, air plasma cutting machines and other ancillary products.
且经营各种气体保护焊机、交直流氩弧焊机、螺柱焊机、空气等离子切割机等配套产品。
GA-1 reducer is used in quantitative output reducer for gas shielded welding and gas explosimeter. It has performance of pressure - reducing and gas flow control.
型减压器是用于气体保护焊与气体测爆仪的定输出减压器，具有减压、控制气体流量的性能。
The national standard is suitable for welded joint of carbon steel and low alloy steel with gas welding (being used for sheet metal), manual arc welding and gas - shielded welding.
本标准适用于气焊(用于薄板)，手工电弧焊及气体保护焊焊接的碳钢、低合金钢焊接接头。
In order to improve the level of automatic welding in CO_2 shielded welding, the tracking system of welding seam based on arc sensor for CO_2 shielded welding is developed in this paper.
为了提高CO_2气体保护焊的自动化水平，本文研制了用于CO_2气体保护焊的电弧传感焊缝跟踪系统。
It can provide several high performance welding modes, such as constant-voltage submerged arc welding, constant-current submerged arc welding, gas shielded welding and carbon arc air gouging.
它能提供多种高性能的焊接模式，如恒压埋弧焊、恒流埋弧焊、气保焊、碳弧气刨。
The joint microstructure and mechanical properties of high strength bainitic steel plate were studied by CO2 gas shielded welding(CGSW), submerged arc welding(SAW) and manual arc welding(MAW).
利用二氧化碳保护焊、埋弧焊、手工电弧焊研究了高强度贝氏体钢板焊接接头的组织和力学性能。
Even with resistive loads, the capacitance of a shielded connecting cable may cause relay welding.
即使对于电阻性负载，屏蔽电缆的电容也可能会导致继电器触点焊接。
Shielded Metal Arc Welding, Submerged-arc Welding and CO2 Arc Welding are recommended for base layer welding.
基层的焊接，推荐采用手工电弧焊、埋弧焊以及二氧化碳气体保护焊。
To reveal the influence of forced convection on gas shielded arc welding temperature field, the infrared camera was used to investigate the temperature field of the base metal in CO2 arc welding.
为了研究强制对流对气体保护焊温度场的影响，通过红外热像仪检测了CO2气体保护焊的温度场，发现在熔池及其邻近区域温度呈圆锥型分布。
Companies with welding, carbon dioxide gas shielded arc welding, argon, carbon arc gouging, oxygen cutting and other special operations personnel.
公司具备电焊、二氧化碳气体保护焊、氩弧焊、碳弧气刨、氧气切割等特种作业人员。
Welding defects such as collapse of molten pool, burning through, would like to happen in the high efficient gas shielded metal arc welding.
应用高效的气体保护熔化极电弧焊焊接铝合金薄板时，容易出现熔池下塌、烧穿等焊接缺陷。
English Name:Welding and allied processes - Recommendations for joint preparation - Manual metal-arc welding, gas-shielded metal-arc welding, gas welding, TIG welding and beam welding of steels.
简体中文标题：焊接和相关工艺。接缝制备的建议。钢的手动金属电弧焊、气体保护金属电弧焊、气焊、TIG焊接和束焊。
Surfacing process test is made on Q235 steel substrate by shielded metal arc welding process using electrode CHR322 at different welding current condition.
前言：采用焊条电弧焊工艺方法，选用C HR322堆焊焊条在Q235钢基体上以不同的焊接电流进行了堆焊试验。
Fracture toughness of both shielded metal arc welding and gas metal arc welding is almost the same.
焊条电弧焊焊缝的断裂韧性与气体保护焊焊缝的断裂韧性相当。
The temperature field in welding HAZ was studied and analyzed. Welding heat curve was set up by argon-shielded tungsten arc welding experiment.
通过钨极氩弧焊试验，对焊接热影响区温度场进行分析和研究，建立了焊接热循环曲线。
English Name: welding consumables - wire electrodes, wires, rods and deposits for gas-shielded arc welding of high strength steels - Classification.
简体中文标题：焊接消耗品。高强度钢气体保护电弧焊用焊丝电极、焊丝、焊条和沉积金属。分类。
CO2 gas shielded arc welding is widely used in production, but the spatter produced in the weld process badly affects the quality of weld.
CO2气体保护焊是广泛应用在生产中的焊接方法，但因为焊接时飞溅过大影响了焊接质量。
After visual inspection and metallographic test, analysis and discuss the welding zone cracking reasons for 6061 and A7003 aluminum alloy thin-walled tube after TIG (argon shielded arc) welding.
通过宏观及微观检测，分析了6061铝合金管及A7003铝合金薄壁管经TIG(氩弧)焊后的焊接区开裂的原因。
Such as electric arc welding, carbon dioxide gas shielded arc welding, TIG etc.
电弧焊、二氧化碳气体保护焊、氩弧焊等各种焊接。
Surfacing process is conducted on the substrate of steel A3 by shielded metal arc welding process using electrode CHR322 under different welding current conditions.
采用堆焊焊条CHR322，在A 3钢基体上以不同的焊接工艺进行手工电弧堆焊试验。
The results show that self-shielded flux-cored welding wires have better mechanical properties and wider applied scope than submerged arc welding wires in repairing the continue cast rollers.
结果表明，修复连铸辊，自保护焊丝比埋弧焊丝具有更好的力学性能及更宽的应用范围。
The droplet transfer in the twin-wire co-pool gas-shielded metal arc welding(TCGMAW) process greatly affects the welding seam appearance and the welding quality.
双丝共熔池气体保护焊（TCGMAW）的熔滴过渡对焊缝成形以及焊接质量具有重要的影响。
The droplet transfer in the twin-wire co-pool gas-shielded metal arc welding(TCGMAW) process greatly affects the welding seam appearance and the welding quality.
双丝共熔池气体保护焊（TCGMAW）的熔滴过渡对焊缝成形以及焊接质量具有重要的影响。
应用推荐