This research method can provide a new method to obtain reliable shear strength parameters of intact sliding zone soil.
该研究方法可为获取真实有效的滑带土剪切强度参数提供一条新思路。
Secondly, Luojiashan soil samples were selected for the unsaturated triaxial tests and the shear strength parameters were obtained.
然后选取珞珈山土样进行了室内非饱和土的三轴剪切试验，得出试验土样的抗剪强度参数。
Furthermore, the unloading shear strength parameters should be applied when using total stress method to analyse excavation problems.
此外，对于基坑开挖采用总应力法分析时，应按卸载总应力强度指标计算。
Based on the tri-axial test results, the influence of water content and shearing bearings on Lanzhou s loess shear strength parameters.
对兰州原状黄土不同剪切方位、不同含水量试样进行了一系列常规三轴不固结不排水剪切试验研究。
According to the analysis, the authors conclude that the unloading shear strength parameters should be used when applying total stress method.
经过分析，作者认为当采用总应力法计算时，原则上应采用卸载强度指标。
The shear strength parameters of rock masses are generally most important and difficult to determine when performing stability analysis of rock works.
岩体抗剪强度参数的确定是进行岩体工程稳定性分析中最基本和最重要的，也是最困难的一项工作。
Finally, in combination with quantitative indexes determinied in the code for "Design of Concrete Gravity Dams", the shear strength parameters of weak structural plane are determinied.
并结合《混凝土重力坝设计规范》中提出的用粒度成分定量指标选取软弱结构面抗剪强度参数，对软弱结构面抗剪强度参数取值问题进行了探讨。
The field measurements are also been performed using the pressuremeter tests. The method used to calculate shear strength parameters of the solid waste by pressuremeter curves are presented.
在垃圾填埋场进行现场旁压试验，给出了一种利用旁压曲线推求强度指标的方法。
The parameters in the aeries include: amount of longitudinal reinforcement, amount of transverse reinforcement, shear span-to-depth ratio, thickness of tube wall and strength of concrete.
试验中的主要参数有：纵向钢筋的数量、横向配筋率、剪跨比、管壁的厚度及混凝土强度。
The parameters of shear strength of slide zone soil are indispensable factors for stability evaluation and countermeasure design to landslides.
滑带土抗剪强度参数的正确选取，是滑坡稳定性评价和抗滑工程设计中的关键问题。
With no yielding up to its fracture strength of CFRP, the stress of CFRP at the maximum shear loading is found to be the key parameters in determining shear strength of the columns.
由于碳纤维布无屈服现象，故达到最大荷载时碳纤维布的应力是确定加固后柱受剪承载力的关键参数。
The finite element model of steel plate shear wall with silts in frame is established and by which the effect of main silt parameters on its strength and stiffness is analyzed.
建立了带框架的开缝钢板剪力墙有限元模型，分析了主要开缝参数对其强度和弹性刚度等性能的影响。
Wall thickness of steel tube, concrete strength, shear-span ratio and axial force ratio were considered as test parameters.
试件参数包括钢管壁厚、混凝土强度、剪跨比和轴压比。
Furthermore, it is pointed out that the restorations of residual shear strength on time effect are considered on analysis of the parameters of the fossil landslide slip surface.
同时指出，古滑坡滑动面的抗剪强度的分析应考虑时间效应下残余强度的恢复。
Parameters of shear strength from triaxial compression test are widely used in project construction.
在工程建设中三轴压缩试验提供的土体抗剪强度参数得到越来越广泛的应用。
With the development of the study, it is potential of the estimation-method to directly provide the parameters of the shear strength of rock joints replacing the direct shear test.
随着研究的不断深入，估算方法有可能替代直剪试验直接提供岩体结构面抗剪强度。
The direct shear tests are more accurate in simulating friction behavior between blocks of solid waste feasible to determine the strength parameters of solid waste.
直接剪切试验更准确地模拟了垃圾团间的滑动摩擦特性，用直接剪切试验确定垃圾土的强度参数更合理；
Based on adjustment of model parameters in finite element analysis, the influence of brittle property of high strength concrete on the shear capacity was analyzed.
通过有限元模型的参数调整进行了数值模拟，定量分析了高强混凝土脆性对节点受剪承载能力的影响。
Based on adjustment of model parameters in finite element analysis, the influence of brittle property of high strength concrete on the shear capacity was analyzed.
通过有限元模型的参数调整进行了数值模拟，定量分析了高强混凝土脆性对节点受剪承载能力的影响。
应用推荐