The outcrop fold was a structural feature formed by the crust occurred the left lateral tenso shear shearing under the extentional mechanism in the early period.
露头褶皱为地壳早期在伸展机制下发生左行张扭剪切作用产生的构造形迹；
Model predictions demonstrated that fibers resist shear even when the shearing direction does not coincide with the fiber direction.
模型预测证明纤维能抵抗剪切力甚至当剪切力方向和纤维方向不一致时。
Influences of composition of the blends, shear stress, shearing rate and temperature on the rheological behavior and viscosity of the melt were discussed.
讨论了共混物的组成、剪切应力和剪切速率以及温度对熔体流变行为、熔体粘度的影响。
By introducing a damage variable expressed by the equivalent shear stiffness, a dynamic shearing damage constitutive model of rock is established including three phases.
定义了用等效剪切刚度表示的损伤变量，建立了一个分三阶段表述的岩石动态剪切损伤本构模型。
Based on dissipation mechanism of shearing power, a new method of modeling dynamic viscosity of polymer melts in vibrating shear flows was proposed in this paper.
基于剪切功率的耗散机理，提出了一种计算振动剪切流场中聚合物熔体动态黏度的粘性耗散法，并建立了理论模型。
The results show that the apparent viscosity of A356 alloy slurry in steady-state decreases with the shear rate increasing under isothermal shearing condition.
结果表明：等温剪切时，浆料稳态表观粘度随着剪切速率的增大而下降，半固态a 356铝合金具有明显的触变性。
Increasing the arch thrust augments the shear stress on the surface of the shearing resistance part, which counteracts the influence of the crushed rock.
同时由于拱向应力的增大，即增大了抗剪面剪应力，抵消了坝体下游破碎岩石的影响。
An equation for the calculation of true shear strain was derived from the integration of infinitesimal shear strain in plane shearing process with constant principal shear strain direction.
对切应变主轴不变的平面简单切变过程，通过无穷小应变的积分，导出了真实切应变计算公式。
Shear Springs are built on the diagonals of quad faces and provide some resistance to shearing forces in the cloth.
剪变弹簧，四边形面的对角线重合。提供抵抗布料剪切变形的力。
Through many direct shearing tests, shear strength of unloading was studied. The concept of unloading ratio and the residual strength were put forth.
通过大量的室内抗剪强度试验，提出了卸荷比、临界卸荷比、极限卸荷比和强度残留率概念。
Shearing Angle can be adjusted within a certain range, which can reduce the shearing deformation of sheet metal and can shear much thicker sheet metal.
刀架剪切角能在一定的范围内调整，可使剪切材料变形量减小到理想状态，又可剪切超厚板料。
The shearing force and overturning moment of column is reduced, and the shear force and moment at the top of pile is decreased compared with linear interaction system.
与线性相互作用体系相比，柱的剪力和倾覆力矩减小；桩顶的剪力和弯矩也有所减小。
The strength of oblique edge shear is analyzed by three dimension finite-element method, through which provides scientific basis for increasing shearing capability.
用有限元法对剪切机机架强度进行分析，为提高剪切机剪切能力提供了理论依据。
Based on the tri-axial test results, the influence of water content and shearing bearings on Lanzhou s loess shear strength parameters.
对兰州原状黄土不同剪切方位、不同含水量试样进行了一系列常规三轴不固结不排水剪切试验研究。
The Woxl-fault in western Hunan is a brittle shear zone characterized by shearing—sliding along its strike.
湘西沃溪断裂为一具走向剪切滑移性质的脆性剪切带。
In this paper, shearing mechanism in the joint core region is analysed from crack to limit state, on the basis of shear test of wrapped steel joint under the monotonic load.
本文根据外包钢节点在单调荷载下的抗剪试验，分析了节点核心区在开裂状态之前及开裂状态到极限状态的抗剪机理，求出了各主要抗剪因素的剪力分配。
Defines shearing and explains how to shear colors using a color matrix.
定义剪切并解释如何使用颜色矩阵剪切颜色。
The later one is of a larger scale and mainly controlled by the R type shearing fracture developed in Jinshan shear zone.
后者主要受金山剪切带内R型剪切裂隙控制，规模大。
Also the characteristics of the hydraulic circuit of the main shear cylinder has been analyzed, and the shearing capacity of the main shear cylinder has been checked.
着重对主剪切缸液压回路特点进行了分析，对主剪切缸剪切能力进行了详细校核。
Compared with conventional flying shear, it has many advantages, such as the scope and range of shearing section and velocity are wide, etc.
与传统飞剪相比，具有剪切断面和剪切速度范围大等优点。
A single axle penetration and direct shear tests, through uniaxial penetration and direct shear correlation of direct shearing test proved reasonable and effective.
进行单轴贯入和直接剪切试验，通过单轴贯入和直接剪切的相关性证明直接剪切试验合理有效。
The study results prove the advantages of groove guided roiling shear in improving the quality of shearing and reducing the peak shearing force.
并对该软件系统进行了可行性验证，通过验证结果，证明了辊轮导槽导向式装置在克服剪切力峰值和提高剪切质量等方面的优越性。
A new method for computing shear strength of reinforced concrete flat plate without shear reinforcement while transferring shearing force only is presented herewith.
提出了无剪切钢筋的钢筋混凝土平板在仅传递剪力时，其抗剪强度的计算方法。
The distribution of storey shearing force in frame-shear wall structure is discussed.
讨论了框剪结构在弹性和弹塑性工作状态下楼层剪力的分配机理。
There are three fracture modes in shearing tests, i. e. , exuviation, shear and crush fractures, with nugget dimensions and shearing loads increasing in turn.
点焊试样剪切试验中存在脱壳式、剪断式和压断式三种断裂模式，所对应的熔核尺寸和剪切载荷依次增加。
On the base of the lateral shear interferometry, different methods of shearing wave front reconstruction are described in this paper.
在横向剪切干涉技术的基础上，讨论了几种波面重建的方法。
To describe the control principle, hardware configuration and software design of a microcomputer control system for specified length shearing of stop shear machine group.
介绍一个板材停剪机组定尺剪切控制系统的控制原理及硬件结构和软件设计。
The discriminant condition avoiding the baroclinic destruction and the method to calculate the shearing resistance are given from the mechanics of shearing resistance and the type of shear failure.
讨论 外节点的抗剪机理及节点的受剪破坏形式，提出了节点 斜压破坏 的抗剪承载力计算方法。
The discriminant condition avoiding the baroclinic destruction and the method to calculate the shearing resistance are given from the mechanics of shearing resistance and the type of shear failure.
讨论 外节点的抗剪机理及节点的受剪破坏形式，提出了节点 斜压破坏 的抗剪承载力计算方法。
应用推荐