The paper proposes a new method for calculating shear plane area based upon a new oblique cutting model with double edge.
根据新的斜角非自由切削模型，本文提出了新的剪切面积计算方法。
Variation of striper force and clearance between punch and die plate with respect to shear plane and die stress were analyzed.
分析了不同压边力和凸凹模间隙对精冲断面质量和模具应力的影响关系。
The results show that the frictions caused by the wall of shear box will influence the distributions of stresses in specimens and the normal pressure stresses on the shear plane.
结果表明，剪力盒壁摩擦力将会影响试验土样中的应力分布和剪切面上的正压应力值。
So a split-type shear box is adopted to conduct the in-situ shear test in order to make the stress on the shear plane uniform and ensure the shear stress to running through the center o.
我们改进后采用分体式剪切盒进行原位土体试验，使剪切面上的应力分布均匀，保证剪力通过剪切缝中心，同时在试验过程中法向及剪向加载时试体稳定性得到了很好的改善。
The results showed that most multiaxial fatigue cracks were initiated and propagated along the direction of maximum shear plane or on the direction perpendicular to the tubular specimen's axis.
研究表明，多轴疲劳裂纹主要是沿最大剪切平面或垂直于管形试样的轴线方向扩展。
An applied tensile or compressive stress resolved into a shear component along a specific plane and direction within that plane.
一个实际拉或压应力沿某一特定平面和在该平面特定方向上分解得到的切应力分量。
With widely applying of profiled sheet, it is not only reflect the working of structure but also obtain benefit that considering the ability resistance to shear of profiled sheet in the plane itself.
随着压型钢板的广泛应用，充分考虑这些面层在其平面内的抗剪能力——受力蒙皮作用，不仅能真实反映结构的实际工作，而且还可获得相当的经济效益。
Presumably it is due to their different critical values of the ratio of slip plane hardening rate to current tensile stress for shear localization.
这可能是由于在不同状态时产生剪切形变局部化的滑移面硬化率对瞬时拉应力的临界比值不同之故。
The final crystalline phase has a FCC structure and the (111) plane is parallel to the shear direction.
最终生成的晶粒具有面心立方结构，其(111)方向平行于剪切面。
Presumably, it is due to their different critical values of the ratio of slip plane hardening rate to current tensile stress for shear localization.
这可能是由于它们产生剪切形变局部化的滑移面硬化率对瞬时拉伸应力的临界比值不同之故。
By adjusting the thickness and space of the shear wall, the problem that the plane is a bit long is solved, and the rigidity distribution and displacement response are reasonable.
通过调整结构剪力墙的厚度和间距解决了建筑平面偏长的问题，结构的刚度分布和位移反应比较合理。
Tranagranular cracks result from deformation damage of grain, and its propagation mechanism is shear rupture along slip plane.
穿晶裂纹源于晶内形变损伤区，其扩展机制为沿滑移面的剪切断裂。
An equation for the calculation of true shear strain was derived from the integration of infinitesimal shear strain in plane shearing process with constant principal shear strain direction.
对切应变主轴不变的平面简单切变过程，通过无穷小应变的积分，导出了真实切应变计算公式。
Under the loading conditions of uniaxial and slightly biaxial tension, the characteristics of material bifurcations (plane shear banding and surface wrinkling) are demonstrated.
文中揭示了在单向和弱双向加载条件下材料分叉(平面剪切带和表面皱曲)的一些特征。
The prediction result of the in plane shear modulus of a typical stitching foam-core sandwich composite was found good agree with the experimental results.
预测典型缝纫泡沫芯材的面内剪切模量，进行夹层结构的面内剪切试验，试验结果与预估结果吻合较好。
The effects of the nonuniformity of porosity development and stress distribution on material bifurcations(plane shear bending and surface wrinkling)are investigated by means of numerical method.
利用数值方法研究材料空洞化和承受应力沿板厚分布的非均匀性对材料分叉（平板中平面剪切带和表面皱曲）的作用。
The approach is based on the assumption that necking mode can be modeled under plane stress conditions and shear localization can be modeled under plane strain conditions.
这种方法是以一种假设为基础的，即可以在平面应力条件下仿照缩颈模式和在平面应变条件下仿照剪切定位，材料是用弹、粘塑性物质构成的仿制品。
The numeric calculation of the tide-effective shear stress on the seismic fault plane is a key to the application in the load-unload response ratio theory.
发震断层面上潮汐有效剪切应力增量的数值计算是应用响应比理论的一个关键性基础问题。
The shear slide plane of a landslide is difficult to find, it is even more difficult to have a clear idea of the slide plane and the characteristics of slide affected zone.
滑坡的剪切滑动面较难查找，而要了解滑动面形态以及滑动影响带特征更为困难。
The influence of shear flow along the magnetic field accompanied with a plane current layer on the tearing instability is analyzed.
在电流片两侧的基态速度场与磁场相互平行的位形下，讨论了速度切变对撕裂模不稳定性的影响。
Bond plane is the tache of weakness for the new and old concrete bond structure when withstanding shear force and tension. Appropriate interfacial agent can improve bond strength.
当承受剪力和拉力时，粘结面是新老砼粘结结构受力的薄弱环节，使用合适的界面剂可以提高其粘结强度。
A comprehensive study of free vibration, buckling and bending of anisotropic simply-supported skew plates subjected to in-plane normal and shear forces is conducted.
对简支各向异性平行四边形板在面内张力和剪力作用下自由振动、屈曲和弯曲问题作了全面的研究。
The free shear layer is a typical flow phenomenon which includes transition and turbulence. The plane jet is a type of free shear flow more complicated than the plane mixing layer.
自由剪切流是一种典型的包含转捩和湍流的流动现象，而平面射流是一种比平面混合层复杂的自由剪切流。
In addition, the layer separation exists in the end of span of overburden if the subsidence happens in whole overburden, which is resulted from the shear failure of the bedding plane.
另外，当覆岩发生整体下沉时离层主要存在于跨度两端，离层由层理剪切破坏引起。
The failure criterion can be judged by the rectangle region in the graph of the relation between ultimate out-of-plane load and ultimate in-plane shear.
它的破坏状态可以用极限面外荷载和极限面面内剪力关系图中围成的矩形区域来判断。
Generally, the contribution of bending stiffness out of plane in shear wall is neglected in engineering analysis.
在计算时一般都忽略剪力墙面外刚度的贡献。
The analysis covers plane strain, plane stress and anti-plane strain shear cases.
分析包括了平面应变、平面应力和出平面应变剪切三种情况。
Once you've chosen your orientation you can scale, shear, rotate (SSR), your bottom plane.
当你要给对象定位时，你可以使用比例缩放，倾斜，旋转（SSR）。这是吉他底层的面。
The method presented here is an extension of the method of analysis of interconnected plane shear walls that had been proposed in an article by the author.
本文的方法，实质上是作者在文章中所提出的分析平面联肢墙的方法的推广。
The fatigue resistance of the butt welds can be improved by means of removing the weld reinforcement and designing the weld in the maximum shear stress plane.
去除焊缝余高或将焊缝设计在最大剪应力平面内可明显改善对焊接头的疲劳性能。
应用推荐