Shear beam model for interface failure was used for the earthquake occurring analysis in this paper.
将剪切梁层间失效模型用于分析地震的发生。
Shear beam model for interface failure was used for the earthquake occurring analysis considering the crucial parameters that affect this model in this paper.
用剪切梁层间失效模型来分析地震的发生并考虑关键参数的变化对模型的影响。
A calculation model for the interfacial shear stress of the reinforced concrete beam strengthened with prestressed CFRP sheets was built based on the elasticity theory after releasing and loading.
采用弹性理论方法，建立了预应力碳纤维布加固钢筋混凝土梁在放张和承载后界面剪应力的理论计算模型。
Based on the test results and analysis, restoring force model of composite steel concrete beam was established with consideration of the degree of shear connection.
在试验研究的基础上，考虑了剪力连接程度的影响，建立了钢—混凝土组合梁的恢复力模型，并编制了相应的计算程序。
Based on this research and using the ultimate equilibrium theory, the calculation model of shear bearing capacity of corroded simply supported reinforced concrete beam is established.
本文在试验研究基础上，运用根据极限平衡理论，建立了锈蚀钢筋混凝土简支梁斜截面承载力计算模型。
This model is developed based on the one-dimensional SMA constitutive equation and multi-cell model, and considers the influence of transverse shear deformation of the hybrid composite beam.
采用多胞模型、形状记忆合金一维本构关系分析方法，同时考虑横向剪切的影响，建立了层合梁的数学模型。
A deep beam model with spring bearing is given, based on the analysis of middle frame of frame and shear wall structure ground floor, which is sensitivity to floor rigidity.
本文从对楼板刚性反应最敏感的构件(即框剪结构的底层中间框架)按刚、弹性计算的剪力误差值的分析入手，建立了一个由弹簧支承的水平深梁的模型。
However, the coupling beam model should be improved to considering the effect of shear later.
但连梁模型有待进一步改进，以模拟短梁的剪切影响。
The shear span ratio can affect the failure mode of RC beams strengthened with GFRP sheets. A theoretical model for flexural behavior of the strengthened RC beam is also developed.
剪跨比对加固梁的破坏形态有影响。根据不同的破坏模式，提出了抗弯承载力计算方法。
Study on the finite element model of shear connector in integration part of composite beam;
钢-混凝土连续组合梁在某些情况下需要按照部分抗剪连接设计。
Based on the 3D analysis result, shear models of ring joint bolt is built and shear parameters between rings needed in 2D analysis with beam-spring model can be obtained by this shear model.
然后，在对三维有限元分析结果研究的基础上，建立了环缝处的纵向螺栓剪切模型，利用该模型可以计算得到错缝拼装衬砌二维梁-弹簧模型中环间剪切弹簧的刚度；
Based on the 3D analysis result, shear models of ring joint bolt is built and shear parameters between rings needed in 2D analysis with beam-spring model can be obtained by this shear model.
然后，在对三维有限元分析结果研究的基础上，建立了环缝处的纵向螺栓剪切模型，利用该模型可以计算得到错缝拼装衬砌二维梁-弹簧模型中环间剪切弹簧的刚度；
应用推荐