Tracking experiment of MIG on V shape welding groove is made with this method, and the experiment result validates the validity of this method.
利用该方法对V形坡口进行了金属熔化极气体保护电弧焊的跟踪试验，试验结果验证了所用方法的有效性。
It showed that the weld cross section with both laser welding processes transformed from nail shape to near X shape with increase of laser power and decrease of welding speed.
结果表明，随激光功率增大和焊接速度降低，复合焊与单一激光焊焊缝的横截面形貌均由钉形向近X形转变。
In addition, the choice of the weld shape strongly affects the welding process and the manufacturing costs.
另外焊缝形状的选择对焊接工艺及制造成本有着重要的影响。
Attention to the need to shape the shape of plastic, steel welding, after a layer of steel wire mesh, and then began to shape the basic layer of paint.
注意需要塑出大概的形状，钢筋焊好之后，在外面扎一层钢丝网，然后开始塑造基础层粉刷。
Note about the shape of the need to model to the, steel welding, outside a layer of steel wire net, and then began to shape the base layer to paint.
注意需要塑出大概的形状臧，钢筋焊好之后，在外面扎一层钢丝网，然后开始塑造基础层粉刷。
The heat of fusion welding is generated in several ways, depending on the sort of metal which is being welded and on its shape.
熔焊的热度有几种来源，取决于被焊金属的种类及其形状。（注重的是翻译出语言的简练）
This approach not only remarkably minimizes the metal spattering, but also results in regularization of particle transfer, increases the stability of welding process and improves the weld shape.
这个方法不仅明显地减少了金属飞溅，而且也使熔滴过渡规律化，增强了焊接过程的稳定性，改善了焊缝成形。
The reasonable joint shape and welding process are obtained, whi ch is to provide better reference for the welding technology of this seam.
通过分析得出其合理的T型接头形式和施焊方法，为压力容器中此类焊缝的焊接提供参考作用。
In multilayer explosive welding of amorphous foils, the regular ripple shape geometry may appear on the surface of foils under certain grancing detonation velocity.
在非晶薄箔的多层爆炸焊接中，箔的表面在一定的滑移爆轰速度下会出现规则的波纹形状。
The article also introduces a new upsetting process with a V-Shape plate, which can not only remove cavity flows in pressing and welding but also improve the distribution of inclusion.
并介绍了一种既能压实焊合空洞类缺陷，又能改善夹杂物分布的新型V型板墩粗工艺。
A particular device of location and compaction for welding by one side in shape by both sides was designed according to the enterprises requirement in steel plates butt joint.
针对某企业需求的平板对接，为解决大型钢板焊接不易翻转的难题，设计了一种单面焊双面成形定位压紧小车。
A method in which a data base and regression will be employed has been studied for predicting weld bead shape and selecting optimum welding parameters in arc welding processes.
本文研究了一种使用数据库及回归分析技术在电弧焊中预测焊道形状及选择最佳焊接参数的方法。
The changing of welding process factors would result in the change of weld size and shape, and have effects on welding quality.
焊接工艺因素的改变会引起焊缝尺寸和形状的变化，进而影响焊接质量。
This series of resistance furnace shape is rectangular, the furnace shell with Angle steel, cold-rolled plate made of the welding, surface electrostatic spraying.
本系列电阻炉外形均为长方形，炉壳系采用角钢、冷轧板焊接制成，表面静电喷涂。
The valve is characterised by heavyweight, special shape, bad welding performance, but demanding excellent welding quality etc.
此类阀门具有质量大、形状特殊、焊接可达性差，焊接质量要求严格等特点；
The investigation of the relationships between weld pool shape parameters and welding process parameters may be beneficial to the quality control of CO2 welding.
在大量工艺实验的基础上，本文进一步研究了熔地形状参数与焊接规范参数之间的关系，从而为CO_2焊接质量控制奠定了基础。
Shield sets the dimensional accuracy and the shape of higher tolerance, the welding seam is also very strict quality requirements.
屏蔽套的尺寸精度及形状公差要求较高，焊缝的焊接质量要求也很严格。
However, it is not obvious in penetration increase for PAW through using of flux compared with TIG welding, but significant improvement in weld shape has been found in PAW.
对于PAW焊，熔深也有增加，但是增加的幅度不如TIG效果明显，但对焊缝成形有很好的改善。
Welding can be large, complex shape and welding assembly irregularly shaped pieces.
可焊接大型、形状复杂及装配形状不规则的焊接件。
The mechanical factors for the property of welding joint are welding defects, discontinuity of joint shape, welding residual stress and welding distortion.
通常，影响焊接接头性能的力学因素有焊接缺陷、接头形状的不连续性、焊接残余应力以及焊接变形。
There are some important factors closely related to the thickness processing including thickness, shape, connective form and welding slope.
则对管件的展开尺寸和形状会产生一定的影响，此时须采取相应的板厚处理。
Sintering can be regarded as welding the particles present in the initial useful shape.
焊接可以被认为焊接微粒当前在最初的有用的形状。
Welding butt joint and angular deformation are easy to take shape during the assembly welding of pressure vessels, especially giant spherical tanks.
压力容器特别是大型球罐，在组装焊接过程中极易产生错边及角变形缺陷，该缺陷的存在将在容器中产生严重的应力集中。
The mathematical model of typical saddle-shape weld was established, and the welding pose parameters were calculated with MATLAB.
针对典型的马鞍形焊缝进行数学建模，并利用MATLAB软件计算焊接位姿参数。
The main factors influencing metal transfer are the component of flux, the shape of wire section, the diameter of wire, the thickness of the steel stripe, and the welding parameters.
影响熔滴过渡的主要因素是：药芯组成物、焊丝截面形状、焊丝直径和钢带厚度以及焊接工艺参数等。
The mathematical model of typical saddle-shape weld was established, and the welding pose parameters were calculated with MATLAB.
针对典型的马鞍形焊缝进行数学建模，并利用MATLAB软件计算焊接位姿参数。
The weld shape directly influences the weld quality, so it is important to predict the weld shape or establish the mapping between the welding process parameters and the weld shape.
由于焊缝形状直接影响焊缝质量，准确地预测焊缝形状即建立焊接工艺参数与焊缝形状之间的映射关系具有重要意义。
Based on the wrought AZ31B magnesium alloy, the effect of the welding parameter on weld shape was analyzed in the course of the TIG welding.
以az31变形镁合金为研究对象，分析了其TIG自动焊过程中焊接工艺参数对焊缝成型的影响。
The results show that the shape of pin, welding speed, rotating velocity, deflected Angle of pin and plunge depth have important influences on the welding formation.
结果表明，搅拌头形状和焊接速度、搅拌头转速、搅拌头偏转角度等工艺参数对焊缝成形有重要的影响。
The results show that the shape of pin, welding speed, rotating velocity, deflected Angle of pin and plunge depth have important influences on the welding formation.
结果表明，搅拌头形状和焊接速度、搅拌头转速、搅拌头偏转角度等工艺参数对焊缝成形有重要的影响。
应用推荐