形状图层选项。
Let's call this layer "Northern Light black shape layer".
让我们的呼吁，这层“北极光黑色形状图层”。
The business card must include at least one vector path, which may be used as a vector mask or a shape layer.
名片必须包括至少一个向量轨迹，该轨迹必须被作为向量屏蔽或成型层面使用。
The pin rectangle encloses the grid intersection point on all four sides by half the minimum metal width of that pin shape layer.
引脚围绕网格交叉点成矩形，在引脚图层通过最小金属宽度的一半指向所有四边。
It sews leaves together in the shape of a cup, then it adds a layer of straw to the inside of the cup and lays its eggs there.
它把叶子缝合成杯状，然后在杯子里面铺上一层稻草，在那里产卵。
Make a new layer and select the "Polygonal lasso tool" and create an abstract shape that looks similar to the example below. it.
新建一个新图层然后选择“多边形套索工具”(Polygonal lasso tool)画出一个类似于下图的一个抽象的形状出来。
Your little one's brain is taking shape inside his oversized transparent skull and a paper-thin layer of skin is covering his whole body.
小不点的大脑在极大的透明的脑壳里正在成形，薄如纸张的皮肤覆盖着他的整个身体。
This is not caused by deeper oceans, more water, at the Equator but rather the shape of the Earth itself, the magma layer in particular.
这不是由赤道处更深的海洋和更多的水体所引起的，而是地球本身的形状，特别是其岩浆层引起的。
Duplicate shape. Add smaller rounded rectangle and from the option bar set it to Intersect. See picture below for its placement. Add following Layer Styles.
重复的形状。新增小圆角矩形，并从选项栏中设置为相交。其位置见下面的图片。新增以下图层样式。
Bevel and Emboss layer styles add 3d effect on our shape.
倾斜和浮雕花纹层风格添加3d影响我们的形状。
Duplicate shape we have just created. Remove all layer Styles used. Set Fill layer to 0% then add layer Style Bevel and Emboss.
重复的形状我们刚刚创建的。删除所有图层样式使用。填充层设置为0%，然后添加图层样式斜面和浮雕。
Duplicate layer shape we have just created and add these layer styles.
复制图层的形状，我们刚刚创建并添加这些图层样式。
Duplicate this shape, and select both layers in your layer palette.
复制该形状，在图层面板中选择这些图层。
Draw shape made of rectangle and triangle. Add following layer styles.
画的形状长方形和三角形。加证明层风格。
Draw a circle shape. Set layer Fill to 0%, add layer styles.
画一个圆圈的形状。设置层填补到0%，加层风格。
Draw a small speaker icon shape. Next to it, create a crescent shape made of two overlapping circle. Add following layer styles, similar to previous buttons.
画一个小发言人图标的形状。它旁边，创造出一个新月形状由两个重叠的循环。加证明层风格，类似于以前的按钮。
Create new layer on top of the rounded rectangle shape.
对创建圆角矩形形状的顶部新层。
Attention to the need to shape the shape of plastic, steel welding, after a layer of steel wire mesh, and then began to shape the basic layer of paint.
注意需要塑出大概的形状，钢筋焊好之后，在外面扎一层钢丝网，然后开始塑造基础层粉刷。
Note about the shape of the need to model to the, steel welding, outside a layer of steel wire net, and then began to shape the base layer to paint.
注意需要塑出大概的形状臧，钢筋焊好之后，在外面扎一层钢丝网，然后开始塑造基础层粉刷。
Fourth, secondary plastering, and then wait for the percent 60 stem degrees according to shape a good scratch, finishes the basement, and according to your requirements of outside layer approach.
第四、做二次抹灰，然后待其百分之60干度时根据造型刮好，作好基底，及根据你要求的外面层做法做。
Draw a thin rectangular shape and add some layer shapes.
画一个薄的矩形，并添加了一些层的形状。
Concrete shape after a few days, the surface is a thin layer of massive fall off, tight get peeling bottom often have "rise sand" phenomenon.
混凝土成型几天后，表面薄薄的一层呈块状脱落，紧挨脱皮的底层通常还会有“起砂”的现象。
Give the shape the following Layer Styles.
给下面的形状图层样式。
To create this shadow i recommend you to create a new layer, place it under the big shape, and then with Brush tool start drawing very smoothly until you are happy with the result.
为了创建阴影，你可以新建一个图层，摆放它到大的形状的下方，然后用画笔工具画一个光滑的阴影直到你满意为止。
Besmear after coating moisture volatilizes then becomes rubber shape of elastomer waterproof layer.
涂刷后，涂膜水分挥发后即成为橡胶状弹性体的防水层。
After rasterizing the shape, I lock off the transparency and duplicate the layer.
在勾扩完外形后，我给透明层解锁，然后拷贝这个层。
In numerical calculations, the effects of rainfall pattern, shape of slope layer and changing slope to the development and decline of subsurface flow were examined.
数值计算验算了降雨的方式，斜坡地层的形状以及坡度的变化对地下水位进展和衰退过程的影响。
Folds of rock layers that have similar mechanical properties or competence tend to be harmonic, with little change in fold shape, symmetry or wavelength from one layer to the next.
相似力学特性质或强岩层的褶皱趋于成为谐调的褶皱，在褶皱形态上、对称性上、或者从一层到下一层的褶皱波长上没有什么变化。
To demonstrate the stability of the magenta layer when the curve shape stabilizing addendum is added, tests on incubation are compared to fresh coatings.
为了证明品层的稳定性，加一种对曲线形状有稳定作用的化合物使老化实验与新鲜涂层进行比较。
To demonstrate the stability of the magenta layer when the curve shape stabilizing addendum is added, tests on incubation are compared to fresh coatings.
为了证明品层的稳定性，加一种对曲线形状有稳定作用的化合物使老化实验与新鲜涂层进行比较。
应用推荐