A shaft position coder is necessary in order to control the rotary robot precisely.
要实现对转动机器人的精确控制，必须进行高精度的角位置检测。
Provides 30 degrees of adjustment to align the signal outputs to the shaft position.
提供30度的调整，使该信号输出轴的位置。
The fast - idle CAM position is controlled by an arm on the choke shaft.
快怠速凸轮的位置是由阻风门轴上的杆臂控制的。
In this position, it must still just be possible to move the ON-OFF operating shaft. For this test, the function of the blocking magnet must be deactivated manually.
在这个位置，需保证仍可以操作手车上的ON - OFF铵钮，进行这个操作时，断路器上闭锁电磁铁的功能应手动解除。
The symmetrical barrel rollers position themselves freely on the concave outer ring raceway, which compensates for any shaft misalignment or flexing.
对称每桶辊位置上自由凹外圈滚道，使用户在任何轴偏心或展示。
The shaft also shall have a directional indicator on top to indicate disc position when the handle is removed.
阀杆也应该在顶部配置方向指示器，用于当手柄拆卸下来时指示阀瓣的位置。
The TPS contains potentiometer, connected directly to the throttle Shaft to sense the throttle position.
TPS包含电位计，与节气门轴直接相连，读取节气门位置。
The fast-idle CAM position is controlled by an arm on the choke shaft.
快怠速凸轮的位置是由阻风门轴上的杆臂控制的。
Generally speaking, in the PMSM (Permanent-magnet synchronous motors) control system, mechanical sensor on the rotor shaft is required to detect the position and speed of the rotor.
一般来说，在电动机调速控制系统中需要在转子轴上安装机械传感器，测量电动机的速度和位置。
The hair shaft and inner root sheath move together as the hair grows toward the surface: the outer root sheath remains fixed in position.
毛干和内根鞘当到达体表时融合在一起：外根鞘仍然保持在原来的位置。
The limit of gravity center position is to assure the uniformity of spring adjustment of shaft weight.
机车重心位置的限制，也是保证机车轮轴重调簧均匀的前提。
Now the general method simplifies the shaft to the line segment, then calculates the distance between two line segments or the position of the point of intersection.
一般的研究方法都是把杆状物体简化为空间线段来进行分析和计算他们之间的距离或者具体的交点位置。
The revolving direction, internal oil hole position and spline shaft of the domestic pump are modified to meet the installation requirement.
为了满足安装的要求，对国产齿轮泵的旋向、内油孔位置和花键轴等进行了改造。
A new method for large shaft alignment was proposed based on visual laser technology and PSD (position sensitive detector) technology.
提出了一种采用位置敏感探测器(PSD)技术与激光技术相结合实现大型轴系对中检测的新方法。
The axial fixed position preload is applied to middle ring of the shaft, the axial rigidity of the angular contact ball bearing is obtained by the impulse excitation tests.
对转台中环主轴施加轴向定位预紧力，通过脉冲激励法试验得到角接触球轴承的轴向刚度，试验结果与理论结果吻合较好，为转台研制中各轴系预紧量的控制提供了理论和实验依据。
Compressing the spring rod, the linkage connected mechanically to the rod of the single-acting cylinder turns the fuel regulating shaft to the stop position.
压缩弹簧杆，联动装置机械连接到单作用汽缸的杆上转动燃油调节杆到停止位置。
As the coded signal changes, the angular position of the shaft changes.
一旦编码信号改变，输出轴的角度位置也将跟着改变。
The depth indictor is an essential instruction instrument in the mine lift system, and its function is to show real-time position of mine skip and the state of shaft switches.
深度指示仪是矿井提升行业中的必备指示设备，其功能是实时显示箕斗的位置和井筒开关的状态。
The high-precision resolver was connected to PMSM with the same shaft to detect the position and speed of PMSM, and Hall current sensor was adopted to detect current of PMSM.
位置和速度的检测采用高精度的旋转变压器和电机同轴相连，电流的检测采用霍尔电流传感器，具有很高的检测精度。
According to the relative position of sub-gear axis parallel shaft spur gear drive, bevel gear drive shaft and intersecting cross-axis helical gears.
按齿轮轴线的相对位置分平行轴圆柱齿轮传动、相交轴圆锥齿轮传动和交错轴螺旋齿轮传动。
At present, in mostly regulation drive systems, the mostly method is to install a position sensor in the rotor shaft.
当前，在大多数调速驱动系统中，最常用的方法是在转子轴上安装位置传感器。
The device can be used for bearing various displacements off a shaft and radial forces, and thus a position sensor has the advantages of high precision and long service life.
该装置可承受各种离轴位移和径向力，从而提高了位置传感器的精度和使用寿命。
It is very important to measure and control the position of bearing hole when machining canular forked shaft.
在叉头套加工过程中，轴承孔位置误差的测量和控制是十分重要。
The running of axes X and Y is driven by servo motor and ball screw shaft and the punching position is controlled by double axes numerical control system.
轴及Y轴运行由伺服电机及滚珠丝杠驱动，由双轴数控系统控制冲孔位置。
Rotor position sensor tracking linked with the motor shaft.
位置传感器的跟踪转子与电动机转轴相联结。
If the cup plug is missing, the park pawl anchor shaft can move out of position under certain conditions.
如果该杯状固定塞脱落，驻车止动爪定位销可能在特定情况下滑移出正常位置。
With the patient in the supine position, the reamers are introduced over the anterior femoral shaft.
患者取仰卧位，磨挫置于股骨干的前方。
With the patient in the supine position, the reamers are introduced over the anterior femoral shaft.
患者取仰卧位，磨挫置于股骨干的前方。
应用推荐