Then, the system constitution, drive form, and control strategy of shaft-less transmission were analyzed and studied.
无轴传动为印刷设备传动系统提供了新的解决方案。
On this basis, the basic model of main-shaft-less concave printer and ADRC are combined to get a new control algorithm.
在此基础上又将推导出的无主轴凹印机粗基本模型与AD -RC相结合，得出新的控制算法。
Fast speed, less empty bags, steady packing capacity. Empty bags' remove device. Double film shaft device, reduce time of stop machine.
包装速度快，空包少，包装性能稳定。有空包排除装置。双纸筒轴装置，减少停机时间。
Bearings with logarithmic profiles are less susceptible to shaft deflection and misalignment.
有对数轮廓的轴承对歪斜和角误差不太敏感。
Wax precision casting is adopted for the shaft sleeve, increasing material utilization ratio by 77% and realizing "less cutting and no cutting".
铸造工艺采用石蜡精铸成型，使材料利用率提高77％，达到少切削、不切削目的；
The results show that stress in hollow beam and semi-shaft bush is much less than permissible stress, while joint of suspension frame and axle housing has too large local stress.
结果表明，驱动桥壳空心梁和半轴套管部分的应力远小于材料的许用应力，而悬架支座与桥壳连接处出现了局部应力过大的情况。
They are usually less efficient than parallel-shaft gears, however, because of an additional sliding movement along the teeth.
他们通常效率较低，比平行轴齿轮，不过，由于一个额外滑运动，沿牙齿。
Discusses the problem of the machining of precision ultra thin shaft by using external cylindrical center-less grinding machine with bracket. The development progress is introduced.
探讨了利用普通无心外圆磨床加辅助附件的方法解决超细长轴的加工问题，介绍了加工超细长轴研制过程。
Reeling is equipped with shaft - less pneumatic cone top device, individual motor drive, double work - place, non - stop high speed automatic picking function, which upgrades the working efficiency.
收、卷采用无轴气动锥顶装置，单独电机驱动，双工位收放料，不停机高速自动接料功能，提高了工作效率。
Note 1 the diameter of the Screw Shaft both ends must be less than the Screw Shaft Root diameter.
注1设计时，请注意使两个轴端不超过丝杠轴底径。
Original shaft with floating ring seal forms a sealed structure, sealed and is less stable.
原泵轴封采用浮动环形式的密封结构，密封稳定性较差。
The CAM shaft is wear resistant and good in comprehensive performance and its manufacture has less steps, short period and low cost.
该凸轮轴耐磨性高，综合性能好，且制造工序少，周期短，成本低。
Motor and gear pump with elastic shaft coupling, coaxial degree is less than 0.1 mm, Angle shall not be greater than 1 degree.
电动机与齿轮泵须用弹性联轴器连接，同轴度小于0.1毫米，倾斜角不得大于1度。
Motor and gear pump with elastic shaft coupling, coaxial degree is less than 0.1 mm, Angle shall not be greater than 1 degree.
电动机与齿轮泵须用弹性联轴器连接，同轴度小于0.1毫米，倾斜角不得大于1度。
应用推荐