The servo power and control lines are routed across the expansion header to provide additional powering options and additional servo ports when the expansion board is installed.
伺服力量和控制线寻址横跨扩展倒栽跳水提供另外的供给动力的选择和另外的伺服口岸当扩充电路板被安装。
As a servo power actuation important part, the center spatial hydraulic pressure servomotor has the important application value in multiple spindle hydraulic pressure simulation table.
作为伺服动力驱动的一个重要元件，中空液压伺服马达在多轴液压仿真转台等领域具有重要的应用价值。
As the existing great power consumption of empty-load or light-load, the bipolar PWM control can be applied only in small or middle power servo control systems.
在轻载或空载时由于存在大的功率损耗，双极性PWM控制只能被应用于中、小功率伺服控制系统。
Vehicle power steering systems control direction and flow of pressure oil with servo valves, then transfer angular inputs from steering wheels to corner angular outputs of road wheels.
车辆液压动力转向系统通过伺服阀控制压力油的方向和流量，把转向盘输入的转角信号转变为车轮的偏转角度输出。
Ratio, servo hydraulic pressure technology, low power pneumatic control valve, production of stuffing.
比例、伺服液压技术，低功率气动控制阀，填料密封生产。
This paper proposes a servo control system for permanent magnet synchronous machine (PMSM) based on Application Specific Intelligent Power Module (ASIPM) and Digital Signal Processor (DSP).
文章提出了采用一种新型专用智能功率模块ASIPM，结合数字信号处理器DSP开发的永磁同步电动机伺服控制系统；
Typical electromechanical integration yuan, components are: power electronic devices and devices, programmable logic controller, fuzzy controller, micro-motors, sensors, ASIC, servo institutions.
典型的机电一体化元、部件有：电力电子器件及装置、可编程序控制器、模糊控制器、微型电机、传感器、专用集成电路、伺服机构等。
The paper takes Rolling Mill Hydraulic AGC servo cylinder as study object to analyze, compare, and optimize the power match design method.
以轧机液压A GC伺服缸为研究对象，对功率匹配设计方法的进行分析、比较和优化。
How to select and calculate the power of the Servo Flying - saw is discussed in this thesis.
本文叙述了如何选择和计算伺服电机的功率。
At present, the pneumatic servo control using on-off valves has become a subject researched on competitively in the domain of fluid power control.
目前用开关阀实现的气动伺服控制已成为流体动力控制领域竞相研究的对象。
Dynamic measurement includes dynamic balance, power efficiency and servo load. The servo load is highly influenced by static lead lag Angle.
动态测量包括动态平衡，功效和舵机载荷。舵机载荷对静前沿滞角度后很敏感。
In order to isolate vibration transmission of marine power plant to decks, an investigation into hydraulic servo active isolation mount for marine diesel set was conducted.
为隔离舰船主机及其动力装置振动向甲板的传递，本文研究了液压伺服主动隔振台架。
Methods of increasing damping radio are introduced for fluid power system, and the pneumatical proportional servo system with variable damping ratio is put forward.
介绍了流体动力系统常用的提高阻尼比的方法，提出了可调液压阻尼器的变阻尼气压比例伺服系统。
According to the structure of servo mechanism on HD2se-ries pump, their functions have been analyzed. The structure and control process of constant power valve are mainly discussed.
根据HD 2系列泵伺服机构的组成，分析了它们各自在HD 2系列泵中所起的作用，着重讨论了恒功率阀的结构和控制过程。
Drive power of direct current servo motor is be introduced, all kinds of its technology are analyzed, development is pointed out.
介绍直流伺服电机的驱动电源，分析其各种技术，指出了发展趋势。
And then the power of servo motor is calculated according to crank press working load, kinematical characteristic, torque and rotational momentum.
以变速驱动压力机的工作负荷、运动特点、工作总功、力矩和角动量为基础，计算其驱动电动机所需的功率。
Intelligent Power IC (IPM) is applied to a radar servo system, which is drived by brushless DC motor. The system can be used in harsh circumstances and get some satisfactory performance.
在无刷直流电动机驱动的雷达伺服系统中，采用了智能功率驱动模块(IPM)来实现功率驱动，它能够满足苛刻的环境要求，并能获得比较满意的系统性能。
Due to the ac servo motor is in brushless structure, almost does not need to repair, the volume is relatively small, be helpful for the improvement of speed and power.
由于交流伺服电机内是无刷结构，几乎不需维修，体积相对较小，有利于转速和功率的提高。
The main circuit consists of intelligent power module (IPM), TM320F240 is used as the control center of firepower-control servo system with higher precision.
系统以智能功率模块(IPM)构成主电路，以TM 320f 240为控制核心组成高精度火控仪伺服系统。
This instrument can output 3v power to servo valve and is convenient for testing servo valve and oil motor at site.
本仪器可输出3V电源给伺服阀，便于伺服阀和油动机现场调试使用。
The hardware of permanent magnet AC servo system is designed, including system power main circuit, system control circuit and auxiliary circuit.
设计了永磁交流伺服系统硬件电路，包括系统功率主电路、系统控制电路和辅助电路。
By added the servo motor, the simulation is realized, and the dynamic analysis is reported, thereby the velocity and acceleration of piston in normal power export state is acquired.
并对正常功率输出状态下曲柄活塞机构的运动进行了动力学分析，得出了活塞的速度和加速度分布。
This paper describes problems about the match of power mechanism in hydraulic servo system.
本文论述了液压伺服系统动力机构匹配问题。
The impact of working stroke to maximum of servo motor power was also analyzed.
分析了工作行程对所需伺服电机最大功率的影响。
Newly designed power supply system. While in machining big surface and deep hole, the computer provides two steps servo feed for superior machining quality and discharge accuracy.
全新电源系统，针对大面积及深孔加工，电脑可选定二段伺服进给速度，加工性能优异并可保持放电精密度。
The power mechanism is the core in the pneumatic servo control system.
在气动伺服系统中，动力机构是其核心。
If the efficiency of servo amplifier is considered, it is practicable that the power supply voltage is about 3 times as large as the servo amplifier output voltage corresponding to rated current.
若考虑伺服放大器效率及电源功率等因素，伺服放大器电源电压应取额定输出电流所对应的伺服放大器输出电压的3倍左右为宜。
High-power big brand double AC servo system: long life time, high precision, fast response, is the foundation of stable work of the printer.
大功率名牌双交流伺服马达，寿命长，精度高，响应快，是喷绘机稳定工作的基础。
High-power big brand double AC servo system: long life time, high precision, fast response, is the foundation of stable work of the printer.
大功率名牌双交流伺服马达，寿命长，精度高，响应快，是喷绘机稳定工作的基础。
应用推荐