This is an alternative to using a serial connection.
这种方法是串行连接的一种替代方法。
For the serial connection, you need the following components.
对于串行连接，需要以下组件。
One extra benefit of using a serial connection is that two incompatible software schemes are used.
使用串行连接的另一个好处是：可使用两个不兼容的软件。
Use a null modem cable to connect the two nodes through their serial ports. Now test the serial connection, as follows.
通过两个节点的串口，使用一根直连线缆将它们连接起来。
When you use a null modem to make a direct serial connection between two computers, your cable must be wired, as shown in Listing 1 below.
当您使用零调制解调器电缆在两台计算机之间建立直接串行连接时，您的电缆必须按下面清单1中显示的方式连接。
One extra benefit of using a serial connection is that two incompatible software schemes are used. One is called SLIP and the other is PPP.
使用串行连接的另一个好处是：可使用两个不兼容的软件。一个SLIP，另一个PPP。
One extra benefit of using a serial connection is that two incompatible software schemes are used . One is called SLIP and the other is PPP.
使用串行连接的另一个好处是：可使用两个不兼容的软件。一个叫SLIP，另一个叫PPP。
The rubber filling oil was preparing using MEK dewaxed oil as raw material, adopting one stage serial connection hydrofining process with RJW-2 catalyst.
以炼油厂“老三套”生产的酮苯脱蜡油为原料，在装有RJW-2催化剂的加氢装置上采用一段串联加氢工艺研制生产橡胶填充油。
The two routers communicated with each other via serial connection, and each router connected to the ThinkPad through Ethernet. This is shown in our connection diagram.
两个路由器通过串行线联接起来，并且每个路由器通过以太网连接到ThinkPad。
The problems existing in manual synchronization circuit and back speedup function of CSL?100 series protective relays at line to line serial connection mode are analyzed.
针对CSL 10 0系列保护装置配置在线—线串接线方式中时，手合同期回路及其后加速功能所存在的问题进行了分析。
Serial connection ? ? ? ? same conditions for all channels small risk of blockage high process security simple monitoring (flow rate, mould temperature) simple connections.
串联连接? ? ? ?所有通道流量相同断路可能性小工作可靠性高检查容易（温度，流量） 检查容易（温度，流量）
The simplest way of getting the data from the Arduino is with the unit connected directly to a host computer Universal Serial Bus (USB) interface, reading the data as if it were a serial connection.
从Arduino获得数据最简单的方式是让此单元直接连接到主机计算机的UniversalSerialBus (USB)接口，像串行连接那样读取数据。
Connection serial reuse within LTC is discussed later.
后面将讨论LTC中的连接串行重用。
Protocol also handles the sending and receiving of messages using a datagram or serial port connection.
Protocol还处理使用数据报或串行端口连接的消息发送与接收。
This behavior is "connection serial reuse."
此行为是"连接串行重用（connection serial reuse）。"
Provides a connection to other computers via a parallel or serial cable.
使用并行或串行电缆连接到其他计算机上。
In this case, you must configure the target computer to accept a serial-port-to-serial-port connection.
在本例中，必须配置目标计算机以接受串行端口到串行端口的连接。
Connection Serial Reuse in LTC.
LTC中的连接串行重用。
ROM emulator ACTS very much like a debug monitor, except that it includes its own serial or network connection to the host.
ROM模拟器动作起来象一个除错监视器，除了它包含自己连到主机上的串口或网络外。
The debugger runs on a host computer and connects to the target through a serial port or network connection.
除错器在宿主机上运行并且通过串口或网络连接到目标机上。
It usually resides in ROM and communicates with a debugger via a serial port or network connection.
它一般被放在ROM中，通过串口或或网络与除错器进行通讯。
It usually resides in ROM and communicates with a debugger via a serial port or network connection.
它一般被放在ROM中，通过串口或网路与除错器进行通讯。
Serial port: The connection for serial interface.
串联插口：连接串联接驳器的插口。
Parallel port The connection for parallel interface. See Serial port.
并联插口连接并联接驳器的插口。参阅串联插口。
The hardware connection drawing of serial interface between MCU AT89C52 and LCD is illustrated.
给出了单片机AT89C52与液晶显示器件的串行接口硬件连接图。
Using single chip as the core, the paper studies a way to realize multiplex low speed data serial transmission, presents hardware connection chart, expounds work principle and software design idea.
以单片机为核心，研究多路低速数据串行传输的一种实现方法，给出硬件连接图，阐述各部分工作原理及软件设计思路。
This paper describes how to actualize the asynchronous communication between synchronous serial port of DSP and asynchronous serial port of PC by simply hardware connection.
本文描述了如何利用简单的硬件连接实现DSP的同步串行口与PC机的异步通讯。
The DC voltage of each serial module can be boosted based on the battery output voltage and the parallel connection of battery groups is allowed.
系统中每个串联单元的直流电压可在电池组端电压的基础上进一步提高，并允许多组电池并联接入。
The DC voltage of each serial module can be boosted based on the battery output voltage and the parallel connection of battery groups is allowed.
系统中每个串联单元的直流电压可在电池组端电压的基础上进一步提高，并允许多组电池并联接入。
应用推荐