Usually, the parameters of the vehicle's control strategies are selected according to experience, and are difficult to be optimized by using conventional methods.
然而，决定整车控制策略的参数较多，一般是靠经验选择，而且难以用常规的方法来优化。
The modification of bamboo/cotton blended fabric is performed with selected cellulase, and the process conditions and recipe are optimized by single factor and orthogonal experiments.
筛选了纤维素酶对竹/棉混纺织物进行改性处理，经单因素试验及正交试验，优化了工艺条件及配方，并对改性后的织物试样进行了综合品质的测试。
The intergrated analysis shows that 8 optimized forestation modes that are high adaptability, high survival rate, flush growth and friendly accreting among spices had been selected.
通过综合分析筛选出了适应性强、造林成活率高、生长旺盛、种间共生性良好的优化造林模式8种。
Aiming at the unmelted powders splash from collision between electron and powders, optimized process parameters is selected to pre-heat the powders to obviously reduce the splash.
针对实验中出现的电子与粉末碰撞造成的未熔粉末的飞溅，采用优化的工艺参数对粉层进行预热，从而大大减少了未熔粉末的飞溅。
Then it optimized the rescue supplies using form operation method based on the result of the shortest path, and selected the optimal transportation scheme.
讨论了一种地理信息系统空间分析算法——最短路径分析，然后利用最短路径结果，采用表上作业法将灾害救援物资进行优化，给出最优调运方案。
Method: Same mobile phase and detection wavelength were selected and suitable precipitating agent was used. The HPLC conditions were optimized.
方法：选择相同的流动相和检测波长，采用适当的沉淀剂，对四种添加剂的检测条件进行了优化。
In the mean time, the main dynamic performance parameters, such as the spring rigidity, oil damper damping, are optimized and selected.
同时，对弹簧刚度、减振器阻尼等各项主要动力学性能参数进行了优化选择。
So we measured the indexes of Kitasamycin Tartrate, such as effect of medicine, color degree, and selected an optimized salt-forming process and freeze-drying curve.
因此，通过测定成品酒石酸吉他霉素效价、色级等理化指标，对成盐工艺、冻干曲线进行优化选。
During design of the layout on diesel engine, we performed one-dimensional flow calculation for turbocharger systems, optimized the valve timing and pre-selected the turbocharger.
在柴油机方案设计时，对涡轮增压系统进行了一维流动计算，优化了气门正时，并预选了增压器方案。采用已知的同类机型的放热率进行了缸内过程的计算。
The analytical conditions were optimized and the best spectrum lines were selected.
优选出最佳仪器工作条件和被测元素分析谱线。
This article has described the research and upgrading of the final heat treatment process for the generator shaft end, the optimized process has been selected and put into the operation.
对发电机轴端头的最终热处理工艺进行了研究和改进，筛选出了最佳工艺条件并进行了实施。
The development status, composition and production process are introduced, and the optimized degumming technique of extracting meyer sedge fiber are selected.
文章介绍了乌拉草纤维的开发现状、成分分析以及生产的工艺流程，对提取乌拉草纤维的脱胶工艺进行了优化选择。
Taken keeping temperature of the sink source working stably and lasting a certain time as target, sink source was optimized and freezing ice was selected as sink source.
以保持冷源工作稳定和一定工作时间为目标，优化选择了冷冻冰作为冷源，并对冷源腔进行了结构优化。
Polymorphous silicon film was selected to be thermal-resistance layer of micro-bolometer, and we optimized the structure of micro-bolometer through optical and thermal design.
选定多形硅薄膜为微测辐射热计热敏层，并重点从光学和热学两方面对微测辐射热计结构进行了优化设计。
Polymorphous silicon film was selected to be thermal-resistance layer of micro-bolometer, and we optimized the structure of micro-bolometer through optical and thermal design.
选定多形硅薄膜为微测辐射热计热敏层，并重点从光学和热学两方面对微测辐射热计结构进行了优化设计。
应用推荐