The flexural strength calculated on the basis of the plane section assumption and strain compatibility condition agrees well with the test results.
根据平截面假定和应变协调条件计算的受弯承载力与实测值符合较好。
Before the failure of bamboo beams, cross-section strain distribution along the height was linear, and the plane-section assumption was established.
竹梁在破坏前,横截面应变沿高度方向的分布基本上呈线性,平截面假定是成立的。
According to the tapered section assumption, this paper presents a method for calculating the local stress of a hollow cylindrical shaft with fillets under tension.
根据锥形截面假设,探讨了一种计算具有圆角的空心圆轴拉伸时局部应力的方法。
The plane-section assumption was not congruous in low strain dynamic tests on pipe piles, so the propagation of stress wave couldn't be expressed by 1D wave equation.
管桩低应变检测时,平截面假定并不满足,应力波的传播不能简单地用一维波动方程描述。
The computation of stress resulted by external load is relatively complex because the deformation of unbonded prestressed strand cannot comply with the plane section assumption.
无粘结筋的变形不符合平截面变形假定,因此由外荷载引起的应力计算比较复杂。
The three-dimensional effects of pile head and applicability of plane-section assumption are main problems in low strain dynamic tests on cast-in-situ concrete thin-wall pipe piles.
现浇薄壁管桩低应变检测时,存在桩头三维效应以及平截面假定的适应性问题。
From 0 load till about 0.8 times the ultimate load bearing capacity, the steel tube longitudinal strain distribution along the depth of cross-section obeys the plain section assumption.
从加载之初直到大约0.8倍的极限承载力,试件纵向应变沿截面高度的分布基本符合平截面假定。
A method to calculate the section curvature ductility index of high strength concrete shear wall is induced by using stress-strain relationship of rectangle stirrup and plane section assumption.
利用矩形箍筋约束混凝土的应力一应变关系和平截面假定,建立了高强混凝土剪力墙截面曲率延性系数的计算方法。
The calculation of flexural strength of reinforced concrete members in Code for Design of Concrete Structures (GB50010-2002) is the equivalent rectangle method based on the plane section assumption.
现行《混凝土结构设计规范》(GB50010-2002)中正截面承载力的计算方法是基于平截面假定的等效矩形计算方法。
Based on plane section computational assumption, the constraint equations of element nodes' degree are used and the simplified finite element method is proposed.
通过平截面计算假定,引入单元节点自由度的约束方程,提出了承载能力有限元计算的简化方法。
Following the process of construction, considering the worst loads, according to the assumption of plane section, the steel girder alone and the composite girder are computed respectively.
按照实际施工过程,考虑最不利计算荷载,根据平截面假定,分别对钢梁单独受力和钢-混凝土组合梁两种工况进行计算。
When box beam is bent, the assumption that the section is plane is not satisfied and the shear lag is produced.
箱形梁弯曲时,平截面假定已不能满足要求,产生剪力滞效应。
With theoretical method based on the assumption of plane section, the influence of steel reinforcement ratio, CFRP amount and initial loading level on the flexural strength is analyzed.
利用基于平截面假定的正截面受弯承载力的计算理论,分析了配筋率、加固量及二次受力等因素的影响。
With theoretical method based on the assumption of plane section, the influence of steel reinforcement ratio, CFRP amount and initial loading level on the flexural strength is analyzed.
利用基于平截面假定的正截面受弯承载力的计算理论,分析了配筋率、加固量及二次受力等因素的影响。
应用推荐