A locator feature (48) indexes receptacle elements on the circuit board (28), alignment tool (100), and seal plate (40).
定位特征(48)标引在电路板(28)、对准工具(100)和密封板(40)上的接受元件。
It also approach theoretically to change the conical valve gag into globe valve gag to raise the stability of the seal plate.
并在理论上探讨将锥形阀瓣改为球形阀瓣，提高密封面的稳定性。
Based on the practical experience and relevant reference, one approximate method for calculating the seal plate of plate bundle was presented as well.
笔者通过对产品开发的生产实践，参照有关资料，提出解决板束封板设计计算的近似计算方法。
The results of the experiments show that the quality of the welding seam between the flange girth of steel beam and the seal plate is very important to the function of the joint;
试验结果表明，钢梁翼缘与封口板之间连接焊缝的焊接质量对节点性能至关重要；
Make a plate of pure gold and engrave on it as on a seal: HOLY TO THE Lord.
你要用精金做一面牌，在上面按刻图书之法刻着‘归耶和华为圣’。
They made the plate, the sacred diadem, out of pure gold and engraved on it, like an inscription on a seal: HOLY TO the Lord.
他用精金做圣冠上的牌，在上面按刻图书之法，刻着：归耶和华为圣。
Seal the blind plate and check carefully whether the pipeline is correctly connected and block phenomenon in the pipe before pressure test.
试压前要先封好盲板，认真检查管路是否连接正确，有无管内堵死现象。
A motor shaft gap used for a sealing plate for a seal air channel is left between the belt pulley and the end cover of the motor shell.
在皮带轮同电机机壳端盖之间保留供密封风道用的密封板穿过的电机轴空隙位。
The oven is made of thin steel sheets, fiberglass is inserted between the working chamber and outer plate of the oven as thermal insulation, there is a seal ring embedded in the door.
烘箱由薄钢板构成，工作室与箱体外壳间以玻璃纤维作保温材料、门面镶有密封圈。
Reattach cover plate to make an air and water tight seal.
重新固定盖板，并紧密密封防止空气和水通过。
A comb plate is arranged in the middle groove chamber, sepharose is used to seal the running gel, and macromolecule sample components can be recovered from the running gel.
在中间槽室中配置梳状板并采用琼脂糖凝胶封固电泳凝胶，可以从电泳凝胶中回收大分子样品组分。
When the current state, the valve plate and valve seat seal between the drive torque on the valve so that pressure to the valve seat.
当逆流状态时，阀板与阀座之间的密封靠驱动装置的力矩使阀板压向阀座。
When no big-size plate vulcanizing press machine, through design deformation mold, could mold big-size high precision O-shape rubber seal on little plate vulcanizing press machine.
在不具备大平板硫化机及大型加工设备条件下，通过设计加工“变形模具”，在小平板硫化机上生产出大规格、高精度的O型橡胶密封圈。
Our factory specializing in the production of copper gaskets, select high-quality copper plate processing and become, mainly used in high temperature and high pressure pipe flanges seal.
我厂专业生产紫铜垫片，选用优质紫铜板材加工而成，主要用于高温、高压的管道法兰密封。
The rubber seal ring is fixed on the valve plate through mechanical means, is firm and convenient for field adjustment or replacing the seal ring.
橡胶密封圈用机械方式固定在阀板上，结构牢固，便于现场调整或更换密封圈。
Each time the shield is lowered, the plate pulls the visor towards the helmet for a snug, waterproof seal.
每个盾是降低时，板对拉一个温暖的头盔护目镜，防水密封。
In case that the mounting plate is bent, the raised structure can also be used as a support point and seal seams with an adjacent plate.
在安装板弯曲时突出结构也作为一个支点，并密封相邻板间的缝隙。
The inner cavity of the casing body is provided with a water stop plate and a seal cavity formed from the water stop plate and the casing body.
在壳体的内腔设有隔水板及由隔水板与壳体构成的密封腔。
This machine was made to seal not only the glass bottles but also the tin-plate cans.
通过增加一个气筒和延时装置，使之不仅可用于玻璃瓶封口，而且可用于金属罐封口。
Cable inlet for bottom elevated cover plate: the cover plate can be dismounted to drill holes and the seal rings are provided.
底部凸台盖板进线，盖板可预先拆下开孔，并配有密封圈。
Adhesive foil to seal the plate.
铝箔胶粘封板。
In order to acquire a good hermetic seal between the diaphragm and the base plate, two sealing methods were used, namely, compound method and crystallite method.
研究了复合法和结晶法两种封接方式，使陶瓷基座与膜片达到良好的匹配封接。
It includes electrolyte membrane, silicone rubber seal ring, multihole anode plate, and free lay mode formed granules of catalyst layer between said electrolyte membrane and multihole plate.
它包括电解质膜、硅橡胶密封圈、多孔阳极板，及在所述电解质膜和多孔板之间的自由铺放的方式形成的催化剂颗粒层。
The seal member (54) and locator bushing (50) may be formed as a single, continuous liquid injection molded framework, including portions (58) encased by the mounting plate (40).
密封件（54）和定位衬套（50）可以形成单一的连续的液体注射成型构架，包括被安装板（40）包围的部分（58）。
The seal member (54) and locator bushing (50) may be formed as a single, continuous liquid injection molded framework, including portions (58) encased by the mounting plate (40).
密封件（54）和定位衬套（50）可以形成单一的连续的液体注射成型构架，包括被安装板（40）包围的部分（58）。
应用推荐