It analyzed main factors of arising spectrum analysis error which including specimen decarburization layer depth, surface roughness, describing, etc.
分析了引起光谱分析误差的主要因素，如试样脱碳层深度、表面粗糙度、描迹等。
It is found that the surface roughness influenced by wheel speed and grinding depth can be attributed to the changing of undeformed chip thickness.
研究发现：砂轮速度和磨削深度对表面粗糙度的影响都可归结为未变形切屑厚度的改变。
For a given channel geometry slope and roughness and a specified value of discharge a unique value of depth occurs in steady uniform flow.
对于给定的河道几何形状、坡度、粗糙度以及规定排水量，均匀稳流中出现唯一深度值。
The results show that the effects on surface roughness are feed speed, depth of cutting , tool rake angle and parts hardness in turn.
结果表明：工件进给速度对表面粗糙度的影响最大，切削深度和刀具前角次之，工件硬度影响最小。
The peak current and pulse duration of single pulse determine the size and depth of discharge crater, so they determine the machining surface roughness and size and shape accuracy.
放电单脉冲的电流峰值和脉宽决定了单个电火花蚀坑的大小和深度，从而直接决定了工件的加工表面粗糙度、形状精度和尺寸精度。
It is also found that, when the water depth is fixed, the Manning roughness coefficient increases as the longitudinal pier spacing increases up to approximately the pier width.
值得一提的是，当水深维持不变时，曼宁粗糙系数也会持续增加直至纵向基桩间距与其宽度相同为止。
To improve surface roughness should be considered from VF and cutting depth while the cutting speed is of a little use.
改善表面粗糙度应重点从进给量考虑和切削深度考虑，切削速度的影响是比较小；
As a result, it demonstrated that atmospheric pressure plasma jet technology can increase the roughness of fiber surface and dye depth, and improve dyeing property of Nylon 6 fiber,...
试验结果表明，常压等离子射流处理可增加纤维表面的粗糙度，增加纤维染色深度，提高尼龙6纤维的染色性能，且对纤维强度无影响。
The interfacial roughness is described quantitatively with average depth of sand pour method.
粘结面的粗糙度以灌砂平均深度定量描述。
The etched depth profile of enamel surface was tested by SEM and digitized by image analysis to detect the roughness of enamel. And the fractal dimension could quantify the roughness.
针对牙齿美白剂对牙釉质表面结构之影响，以扫描式电子显微镜，结合影像分析进行碎形维度分析，将粗糙度（roughness）量化，再以接触角测试分析牙齿 表面的粗糙程度对于亲水性的影响；
The influences of abrasive grain size, belt speed, contact roller's hardness, grinding depth and grinding feeding speed on surface roughness were discussed.
讨论了砂带粒度、砂带线速度、接触轮硬度、磨削深度和磨削进给速度对表面粗糙度的影响规律。
The results show that the Manning roughness coefficient increases with increasing water depth.
试验结果表明，曼宁粗糙系数随水深深度的增加而增加。
The results show that the Manning roughness coefficient increases with increasing water depth.
试验结果表明，曼宁粗糙系数随水深深度的增加而增加。
应用推荐