Rotor scale is a device used in cement industry for accurate measure and transport of powdery coal.
转子秤是在水泥工业中对煤粉进行精确计量和输送的设备。
This paper introduces the basic feature of CAN controller, and presents the hardware and software design about P80C592 chip with CAN controller in the control system of rotor scale.
本文介绍了CAN控制器的基本特点，并给出了带有CAN控制器的P 80c 592芯片在转子秤控制系统中的硬件和软件设计。
The theoretical study shows that static unbalance of the rotor was proportional to displacement of the rotor ; the larger displacement scale coefficient, the higher measuring accuracy.
理论研究表明：转子的静不平衡量与转子的偏移成正比；位移比例系数越大，测量精度越高。
The results show that the relationship between the flow and the height of the rotor is not linear, and that the flow scale on the meter is uneven.
并认为流量与转子所处的高度非线性关系；流量的刻度标定也是非简单线性变化。
Rotor bearing system is the heart of large-scale rotating machinery, as a major way to support, the dynamic problem of tilting pad journal bearing (TPJB) growing concern by the people.
转子—轴承系统是大型旋转机械的核心部件，作为主要支承方式的可倾瓦滑动轴承支承，它的动力学特性日益被人们所关注。
Presently, the method of steady state unbalanced currents is widely used in the field test of torsional vibration characteristics of large-scale steam turbine generator rotor system.
目前大型汽轮发电机组轴系扭振特性的现场试验中广泛采用稳态不对称短路变频激振法。
The revolving system of large-scale vibration mills is simplified into a three rotor system which is joined by two flexible coupling.
通过对大型振动磨机运动特性的研究分析，把其旋转系统简化为由两个柔性联轴节连接的三转子系统。
The hydraulic automatic balancing technology is presented to solve dynamic imbalance caused by the scale in the running of the fan rotor.
通过对转子铜线通风孔的工艺分析，介绍了模具结构及主要零部件的设计和模具使用中应注意的问题。
The above is the scale of our research. It aims to decrease tip vortexes, reduce the flow loss of the rotor and improve the output power of the wind turbine.
目的是在减少叶端漩涡，降低叶轮的流动损失，提高风力机的输出功率，将更多的风能转化为电能。
An experimental investigation into the properties of the wake behind a horizontal-axis wind turbine (HAWT) rotor is carried out at model scale, using a single slanted hot-wire probe.
在水平轴风力机模型不同尖速比条件下，利用旋转单斜丝热线在风轮下游进行尾迹流场速度测量。
The manufacturing technique of rotor coils of 100mw air-cooled turbogenerator is mainly discussed in this paper. And the success of it builds a great foundation for HEC to develop large-scale units.
本文重点介绍了空冷100MW汽轮发电机转子线圈的制造工艺和相关的工艺装备，该转子线圈的研制成功，为哈电公司今后生产更大容量的空冷机组奠定了坚实的基础。
A reduction calculation method based on fixed interface component mode synthesis is applied to analyze nonlinear dynamic stability of an actual large-scale rotor-bearing system.
采用基于固定界面模态综合法的降维方法对大型实际非线性转子-轴承系统稳定性进行了分析。
By the end of 1979, We had produced the full scale forming die of the composite rotor blades of Y-2 type helicopter. The results of the NC machining show that this method is successful.
1979年末，我们加工了全尺寸y—2直升机复合材料桨叶成形凹模，从数控加工的结果看这种方法是成功的。
Based on a high-accuracy and large-scale-parallel method, SA model and detached eddy simulation (DES) based on SA were employed to research the flows of compressor stator-rotor interaction.
本文基于一种并行高精度的静动交接面处理方法，采用了SA模型及基于SA的分离涡模拟DES方法，进行了某压气机静动干涉流动的计算。
Based on a high-accuracy and large-scale-parallel method, SA model and detached eddy simulation (DES) based on SA were employed to research the flows of compressor stator-rotor interaction.
本文基于一种并行高精度的静动交接面处理方法，采用了SA模型及基于SA的分离涡模拟DES方法，进行了某压气机静动干涉流动的计算。
应用推荐