The calculated results of excitation and rotation temperature consistently illustrate the plasma jet is non-thermal in nature.
射流的激发温度和转动温度结果显示，这是一种冷的等离子体射流。
The diameter of actual tangent circle is an important parameter for safety of boiler, the residual rotation is the key factor of flue gas temperature deviation at furnace exit.
实际切圆直径是锅炉稳定安全运行的一个重要参数，炉膛出口残余旋转是造成烟温偏差的主要原因。
Measurement of plasma ion temperature and rotation velocity.
等离子体离子温度和角向速度测量。
Thread demoulding mechanism, injection system, protect mechanism of thread rotation and temperature control system were designed.
设计了螺纹脱模机构、浇注系统、螺纹转动保险机构和温度控制系统。
The relationship between temperature of Northeast China in summer and the earth rotation speed is studied.
该文研究了东北地区夏季温度与地球自转速度变化的关系。
The temperature dependence of probe was also studied and the rotation relaxation time of probe was calculated.
并研究了温度对探针荧光偏振的影响，计算了探针的旋转松驰时间。
The device can set the frying time and temperature, wok stir automatic bi-directional rotation, putting out the material with motor-drive.
该设备能设定炒制时间，自动控制炒食温度，炒锅自动双向转动翻炒，电动升降出料。
Tell me the oil temperature, oil pressure and rotation speed at present?
现在的油温、油压、转速是多少？
In the parallel channel rotation problem, secondary flow will uniform the velocity and temperature profile and lead to heat transfer enhancement.
平行通道旋转流动换热问题中旋转产生的二次流使截面的速度和温度分布趋于均匀，从而换热得到强化。
In circular firing system, residual rotation of airflow at furnace outlet is the main reason for gas temperature deviation between two sides of furnace outlet and horizontal gas duct.
四角切圆燃烧锅炉炉膛出口气流的残余旋转，是形成炉膛出口和水平烟道两侧烟温偏差的重要原因，可造成高温受热面热偏差和超温爆管。
Hot air curtain is strong airflow generated by the rotation of the fan rotor, curtain like flow out a certain velocity and temperature, forming a invisible curtain.
热风幕是通过风轮的转动产生的强大气流，送出一定速度和温度的幕状气流，形成一面无形的门帘。
The welding temperature was directly proportional to rotation speed.
提高搅拌头的旋转速度可以成比例地提高焊接温度；
The test must work in a specify rotation spectrum, temperature spectrum and load spectrum to analogize the reality condition.
实验器要在一定的载荷谱、温度谱、转速谱条件下工作，模拟轴承的实际工况。
Because this method performs the measurement within the flip coil rotation time, it is not affected by the temperature dependence in the power supplies and the measurement devices.
因为这种方法在反位线圈转动时间内执行测量，所以不受对温度依赖较大的电源与测量装置的影响。
The higher the temperature and the longer the resident time was, the higher the oligomer content was during polyester melt trans - fer course at a fixed screw rotation speed.
在一定的螺杆转速下，温度越高，停留时间越长，聚酯熔体输送过程中齐聚物含量越高。
The effect of spinning temperature, spinning pressure and rotation velocity on the fiber's degree of profile and effective filament diameter was analyzed.
研究了纺丝温度、压力、收丝速度对纤维异形度和当量直径的影响。
The results were showed that the profile degree of trilobal PCS fibers decreased with a rise in spinning temperature, spinning pressure and rotation velocity.
结果表明：纤维异形度随纺丝温度、纺丝压力、收丝速度的升高而降低。
Light rotation film can raise the greenhouse's temperature, enhance the photosynthetic efficiency, and accelerate the crops growth.
转光膜能能提高棚温、增强光合速率，促进作物生长。
With increasing shaft speed of rotation, heat evolution and temperature rise become a critical problem.
由于轴的转速越来越高，轴承的发热和温升是个突出矛盾。
Distribution of light intensity, transmittance of fabrics, speed of rotation, temperature and humidity have influence on the test precision.
光强分布、织物透光、旋转速度、温湿度等都会影响测试精度。
In a controlled chamber stress experiment, we tested the damage index and mortality of cuttings caused by low temperature of 54 short-rotation eucalypt clones.
本试验共测定了54个短周期桉树无性系在人工气候培养室中的低温胁迫伤害指数和死亡率。
The mechanical properties of materials were characterized and Effect of different synthesis conditions to mechanical property such as temperature, rotation and time were investigated in detail.
熔融共混法加工过程中的混合温度、转速、时间对材料的成型和性质有着显著的影响，为得到最好的实验工艺。
The rotation speed of the fan under assumed temperature reduced thrust takeoff is calculated based on the analogical condition of engine.
假设温度减推力起飞的风扇转速由发动机相似条件计算。
Thirdly, the parameters deciding the quality in polishing process are as follows: slurry, polish pad, pressure, temperature, rotation speed, wafering time, and so on.
在抛光工艺中，抛光液的种类、抛光垫的选择、抛光压力、温度、抛光盘转速、加工时间等诸多条件都是决定抛光质量的重要因素。
In addition, the model is suitable only when the inoculation conditions such as medium, temperature and rotation are invariable, otherwise the parameters of the model should be recalculated.
另外本模型只在培养基成份、培养环境等条件不变时适用，否则模型参数需重新估计。
It is investigated that the influence of barrel temperature and rotation speed of screw rod of extruder on conductivity and strength of the ABS resin composites filled with carbon fibers.
研究了单螺杆挤出机挤出温度及螺杆转速对沥青炭纤维填充abs树脂复合材料导电性及力学性能的影响。
Wash plate unit adopted the brush rotation type to wash plate, have automatic solvent constant temperature device, set 2 drawer drying.
洗版为毛刷转动式洗版，带自动溶剂恒温装置。设二层烘版柜。
Wash plate unit adopted the brush rotation type to wash plate, have automatic solvent constant temperature device, set 2 drawer drying.
洗版为毛刷转动式洗版，带自动溶剂恒温装置。设二层烘版柜。
应用推荐