The influence of rolling speed is not distinct.
轧制速度对界面结合的影响不明显。
According to the main engine you can adjust the reel's rolling speed.
可依搭配之主机调整线轴转动速度。
The rolling speed for plate mill is generally controlled by operator's experience.
目前国内中厚板轧机主传速度基本上由操作员的经验来控制。
With the increasement of rolling speed, rolling mill vibration problems happen very often.
随着轧机速度的提高，轧机振动现象频繁出现。
Car retarder is equipment applied in mechanical and automatic hump marshalling yards for regulating rolling speed of sets of car.
车辆减速器是机械化驼峰和自动化驼峰编组场用来调整车组溜放速度的设备。
The influence of the foiling oil viscosity and rolling speed and reduction rate on the film thickness are investigated with those methods.
借此方法研究了轧制油粘度、轧制速度与压下率对轧制变形区油膜厚度的影响。
The higher the normal load, the smaller the effect of the lubricating oil inlet temperature and rolling speed on the traction coefficient.
随着载荷增大，入口油温和滚动速度对拖动系数的影响减小；
As the rolling speed of the high speed wire rolling mills is very high, the accidental fault is very easy to come out on the transmission parts.
高速线材轧机由于转速较高，其机械传动系统易出现突发故障。
At a low steel rolling speed, the traditional AGC feedback control is not very good due to a long time delay caused by the thickness measurement.
在低速轧钢时，由于测厚仪测量值的长时间滞后，传统的后馈控制效果不好。
The control process of bar rolling speed was presented and the effects of low tension, loop and cascade control in speed regulation were described.
介绍了棒材轧线的系统结构及轧机速度控制过程，详细说明微张力、活套以及级联控制等在速度调节中的作用。
On the basis of the limited conditions, entry thickness, exit thickness, rolling speed, tension, rolling force and rolling torque, etc. are calculated.
根据极限条件，计算出入口厚度、出口厚度、轧制速度、张力、轧制力、轧制力矩等。
Approximation of screwdown value, rolling speed and an iterative method were used to study the maximum screwdown ratio, speed, tension and deformation ratio tolerable in the mill.
作者用压下逼近法、速度逼近法及迭代法研究了该轧机允许的最大压下率、速度、张力和变形率。
Setting main parameters of disc flying shears are presented in detail. including cut Angle, bite conditions, amount of scissors overlapping, friction coefficient and rolling speed etc.
详细介绍了圆盘式飞剪各主要参数的确定，包括交角、咬入条件、剪刃重叠量、摩擦系数、轧制速度等。
Feeding rate, the kiln incline degree and the kiln rolling speed are adjusted to study the changes of particles mean residence time (MRT), mean volume flow (MVF) and loading rate in the kiln.
通过改变给料率、回转窑倾角、回转窑转速来考察它们对物料在回转窑内的平均停留时间(MRT)、平均体积流率(MVF)、填充率的影响。
It is found that, with the rising of rolling speed, the temperature of finished product is raised greatly, and the temperature difference between head and end of the product is reduced apparently.
随着轧制速度的提高，成品终轧温度明显升高，头尾温差大幅度减小；
When under the same axle load, if the wheel rolling speed gets higher, the adhesion coefficient declines as the ratio of the mean asperities contact pressure to the total pressure becomes smaller.
研究发现：相同轴重下，滚动速度越大，粗糙峰接触压力与总压力的比值越小，导致轮轨之间的粘着系数下降；
Rolling speed is a very important part of rolling schedule in setup calculation.
速度制度是轧制规程设定计算的重要组成部分。
Rolling speed is a very important part of rolling schedule in setup calculation.
速度制度是轧制规程设定计算的重要组成部分。
应用推荐