Al ball skewing rolling pass design firstly has used design project of two grooves rolling.
铝球斜轧模具设计首次采用了双头轧制的设计方案。
It keeps the method of calculation rolling pieces and pass design respective - ly from making error by using method of reducing non-linear equations.
采用求解非线性方程组的方法设计孔型尺寸，避免了因轧件尺寸和孔型尺寸分别计算所造成的误差。
The flat die steel production line product; main product: high alloy flat die steel rolling program and pass design at Fushun Special Steel Co.
介绍了抚顺特殊钢有限公司模具扁钢生产线生产工艺；主导产品：高台金模具扁钢轧制程序设计及孔型设计。
In order to improve single productivity, and got parameters of steel ball rolling, This paper has done pass design and experiments of two grooves rolling steel ball.
为提高球磨钢球的单机生产率，并获取钢球轧制的力能参数，进行了钢球双头轧制孔型设计及实验。
The superlority and feature of using big bite in pass design of section rolling were briefed.
叙述了型钢轧机采用大辊缝孔型设计的优点和设计特点。
This paper discusses the effect of rolling process and pass design on product quality for the flat spring steel with single-side and two-slot.
本文阐述了单面双槽弹簧扁钢的轧制工艺及孔型设计对产品质量的影响。
Optimization design of pass and computation of the main driving motor power under operation show that the rolling energy consumption may be reduced by 3.19%.
优化孔型设计与现场主电机功率值的计算表明，轧制能耗可减少3.19%。
The rolling pressure on high speed untwist wire rod mill was measured firstly and succeeded internationally for optimizing technology, pass design, and management of the plant.
首次对高速无扭线材轧机粗轧机组压力进行测试并取得成功，为优化工艺规程、优化孔型设计及设备全过程的经济管理与改进提供了可靠的依据。
In this paper, the principles which should be adhered to when designing skew rolling tool and the pass design for three-roller combining piercing and rolling are discussed.
本文论述了斜轧工具设计所应遵循的原则与三辊联合穿轧的孔型设计。
Some principles for pass design, heating and rolling are summarized when produced sketch blank with bloom, and some measures are put forward to assure the product quality under its peculiarity.
本文论述和总结了初轧机生产异型坯时，在孔型设计、加热、轧制方面应考虑的一些原则。
This dissertation can gain the size of profiled bar in any pass and design the proper pass by calculating the deformation and rolling-force of the steel in the pass .
本论文开发的软件的主要功能是通过计算轧件在劈分孔型中的变形以及受力来确定轧件每个道次轧后断面形状从而设计出合理的孔型。
The rolling mechanism was studied in this paper. The rolling process and the design of pass of rolling mill were researched, meanwhile, the rolling pressure of Y-type rolling mill was also calculated.
本文从研究轧制原理入手，对轧制工艺及孔型设计进行了深入研究，给出了Y型轧机轧制压力计算。
This program can be widely used, such as in roll pass design, the imitation of practical production and the calculation of allocating rolls in continuous rolling.
该程序通用性强，除能设计外，还能进行生产模拟计算，连轧配辊计算。
Aimed at a uniform distribution of driving torques, an optimization design of pass parameters is carried out for primary bar rolling mills.
以某棒材粗轧机组力矩均衡分配为目标，对各孔型尺寸进行了优化设计。
It is introduced how to design reasonable pass and determine the tolerance in rolling with negative tolerance to keep the production steady.
介绍了唐山钢铁公司中型轧钢厂在实行负偏差轧制中，如何设计合理的孔型和确定合理的负度，以保证负偏差轧制顺利进行。
The basic conception and characteristic of X-H rolling method are introduced and X-H pass design technology is recommended.
介绍了X - H轧制法的基本概念及特点，推荐了X - H孔型设计的基本方法。
The basic conception and characteristic of X-H rolling method are introduced and X-H pass design technology is recommended.
介绍了X - H轧制法的基本概念及特点，推荐了X - H孔型设计的基本方法。
应用推荐