Big roller diameter, high efficiency.
大，熨烫效率高。
The needle roller diameter decreases towards the ends.
针滚直径越向末端越小。
It is the basis to determine the roller diameter position and strain analysis.
它是确定轧辊滚动直径位置和张力分析的基础。
An improperly designed hot roller can cause fabric edge in excess of rolling pressure due to the increased roller diameter near the journal ends.
不适当的热轧辊设计会导致织物边缘过度轧压，这是因为热轧辊端部附近直径增大引起的。
The designed parameters of mechanical capabilities of the roll caster should be raised when rolling pressure increase with roller diameter increase.
随着铸轧辊径增大，轧制压力增大，因此铸轧机力能设计参数也要相应增大。
To deduce the formulas for evaluating feed diameter, roller diameter and rolling moment of flattener, obtain the practical formulas and give a computer program.
对扁丝机的进料直径、轧辊直径和轧制力矩的计算公式进行推导，得出了实用计算公式并提供了计算程序。
The paper introduces the difficulties of roller spray welding technique such as controlling for distortion, keeping for layer evenness and dimension of roller diameter.
就轧辊喷焊的技术关键问题：变形控制，涂层均匀性的控制，喷焊后辊子外径尺寸控制及轧辊的组焊工艺等，作以介绍。
STAND: Overall width of the assembled bearing; refers to the combination of sizes of the cone, outer diameter, cup, inner diameter, and roller.
座高：整套轴承的总宽度；参考内外圈尺寸，外径，内径以及滚子。
For needle roller bearings without inner ring, a suitable internal clearance is achieved by selecting the appropriate tolerance for the raceway diameter.
对于无内圈滚针轴承，通过为滚道直径选择合适的公差，可得到合适的内部游隙。
Side guide system: with multiple roller wheels of small diameter.
侧规系统：多个小直径辊轮的固定侧规。
Problem reason, solution and design process of calendar different - diameter roller exchange in nonwovens production line are introduced in the paper.
介绍了非织造布生产线中双辊热轧机不等径轧辊互换问题的提出原因、解决方案及设计过程。
Design and calculation method of the key parameter such as the diameter of roller and pulling force are given.
介绍两辊式和三辊式机械弯曲除锈原理，给出关键参数如辊子直径、牵引力等的设计计算方法。
Specification for bearings - airframe rolling single row, self aligning roller bearings in steel diameter series 3 and 4. Dimensions and loads.
轴承规范。钢的3号和4号直径系列机体单列自调心滚子轴承。尺寸和负荷。
Method: Inspect the influence of roller press, roller speed and the water content of extract powder on yield and friability of particle diameter.
方法：考察轧轮压力、轧轮转速和浸膏粉含水量对颗粒得率和颗粒脆碎度的影响。
Diameter of driving roller for rewinding is large, is the idea equipment for cutting jumbo roll paper.
复卷驱动辊直径大，是作原纸分切的理想设备。
By the way of improving roller dimensions, roller number, outer roller path diameter, stop groove diameter and the effective thickness, the using reliability of the bearing is advanced.
通过对轴承结构中的滚子尺寸、滚子数量、外圈滚道直径、止动槽直径公差及有效壁厚的改进，提高其使用的可靠性。
A speed determining unit determines the transport speed according to the rotation number and a diameter of the free roller.
速度确定单元根据自由辊的旋转数和直径而确定输送速度。
The guide roller ensure the ring rolled comfort, and inspect roller check the rings diameter whether reach the limit dimension.
导向辊保证轧制平稳进行，检测辊（信号辊）测量轧制环件尺寸是否达到要求以停止轧制。
Influencing rules of model's accuracy are obtained when diameter of roller differs. The reasonable advice on drawing up the process specifications is proposed.
并得出不同轧辊直径对神经网络模型精度的影响规律，对轧制工艺规程的制定提出了合理建议。
The paper undertakes the theoretical analysis and the experimental research on measuring principle and accuracy of the apparatus used to measure large diameter with roller method.
本文对滚轮法大直径测量仪的测量原理、测量精度进行分析和实验研究。
Type KAS-3 integrated multiparameter device allows dynamic measurement on rotary kiln axis, tyre clearance and diameter, supporting roller position and diameter.
K AS - 3型集成式回转窑轴线多参数测量仪，能在生产中对回转窑轴线、轮带间隙及直径、托轮位置及直径多参数进行动态测量。
The rolling transmission is driven by a vector frequency motor and floating roller system and PLC can automatically calculate the reel diameter, achieving the reeling tension conical control.
收卷传动采用矢量变频电机﹑浮动辊系统组成，并通过PLC自动计算卷径实现收卷张力锥度控制；
Start of volume production of the world's smallest drawn cup needle roller bearing (2 mm shaft diameter) for a motor application in electronics manufacturing.
开始批量生产世界上最小的制定杯滚针轴承(2毫米轴径)的电机中的应用电子产品制造。
The main technical problem was bearing inner diameter profile grinding, during processing new product YA2, so that the diamond contact roller adjuster was designed.
新产品YA2轴承加工中的主要技术难点是轴承内径成形磨削，为此设计了金刚石滚轮修整装置。
Methods The influence of roller pressure, roller speed, and water content of extract powder on yield and friability of particle diameter was investigated.
方法考察压轮压力、压轮转速和浸膏粉含水量对颗粒得率和颗粒脆碎度的影响。
The large size diameter of step roller operates minimizes the noise and prolongs the product life.
大直径的梯级滚轮，运行平稳，噪音更小，寿命加长。
Machining of workpiece's outer diameter, tapered face, end face, R face, etc. Is available by changing the shape of roller.
通过改变滚轮的形状可实现工件外径、锥面、端面、R面等广泛加工。
Machining of workpiece's outer diameter, tapered face, end face, R face, etc. Is available by changing the shape of roller.
通过改变滚轮的形状可实现工件外径、锥面、端面、R面等广泛加工。
应用推荐