Unwinding adopts magnetic powder brake, roll diameter calculated automatically by the PLC automatic tension control.
放卷采用磁粉制动器，由PLC自动计算卷径实现自动涨力控制。
These factors include ratio of upper and lower roll diameter , reduction ratio , enterance angle and roll rotation speed.
因素有上下轧辊直径比、压下率、导入角和轧辊转速。
The paper also discussed how to select and calculate the roll diameter of a gear, it will be helpful for the gear design.
讨论了齿轮量柱直径选取原则和计算方法，对齿轮设计有特定白勺帮助。
The movement distance single detected by the linear shifter and caused by the increasing of the roll diameter is fed back to the actuating motor.
线性位移器将检测到的卷径增大所移动距离信号反馈给伺服电 机。
T he relation of the four parameters with initial slab thickness, initial slab width, width reduction and edger roll diameter was obtained and a new mathematical model was accomplished as well.
得出表征立轧时轧件断面特征的四个参量与侧压量、立辊直径、板坯来料厚度及宽度间的关系，并建立了新的数学模型。
The paper introduces some methods for diameter compute, velocity measurement, tension control, the same shaft series twice motors control and load balance control of twin drive roll.
介绍了卷径计算、线速度测量、张力控制、同轴串联双电机控制、上下辊负荷平衡控制方法。
The groove depth of the warping roll is as long as a half of the cord diameter. The nip between the pressure roll and No.
整经辊的沟槽深度等于帘线直径，压力辊的沟槽深度为帘线直径的一半。
The device can be compressed into a roll material wire diameter, and increased the density of the material, length.
本设备能将材质一次压缩成滚丝直径，且增强了材质的密度，长度。
The loading pressure is calculated separately for each rider roll depending on the required nip pressure and respective sheet length. The related diameter–dependent set curve is stored in TRUTEC .
加载压力被单独为各自的骑辊加压，根据压区压力要求和各自的复卷长度，相关的纸卷直径，根据在TRUTEC设定的曲线。
There are also two roller straightening machine, relying on two rollers (Concave Intermediate, hyperbolic roll) the perspective of the different changes in the diameter of the material straightening.
也有两辊矫直机，依靠两辊(中间内凹，双曲线辊)的角度变化对不同直径的材料进行矫直。
The designed parameters of mechanical capabilities of the roll caster should be raised when rolling pressure increase with roller diameter increase.
随着铸轧辊径增大，轧制压力增大，因此铸轧机力能设计参数也要相应增大。
This press consists basically of a large-diameter (up to 3 m) center roll which is internally heated by steam injection (up to 3 bar).
这种压榨基本上由一个大直径(高达3米)中心辊，内注蒸汽加热(最多3吧)。
The roll lapping machine is one of the equipments processing the excircle surface of minor diameter workpiece by lapping. The working accuracy is affected directly by the guide wheel of this machine.
滚研机是小直径工件外圆表面研磨加工设备之一，该机导轮表面形状直接影响加工精度。
Diameter of driving roller for rewinding is large, is the idea equipment for cutting jumbo roll paper.
复卷驱动辊直径大，是作原纸分切的理想设备。
Diameter of driving roller for rewinding is large, is the idea equipment for cutting jumbo roll paper.
复卷驱动辊直径大，是作原纸分切的理想设备。
应用推荐