In this paper, the method of pulsating hydraulic test to relief retaining ring stress is introduced.
本文介绍用油压脉动方法调整护环的宏观残余应力。
The design of piston ring depends on the rightly selected dimensions, so that the piston ring tension can meet the demand stipulated with its stress in the allowed range.
而活塞环的设计在于选择合适的尺寸，使活塞环弹力满足要求的同时应力也在许可范围内。
The technique and its principle of high temperature strain measurement are introduced to determine heat sleeve stress about rotor retaining ring of large turbogenerator.
本文简要介绍了高温应变测量原理和技术在大型汽轮发电机转子护环热套应力测试中的成功应用。
The fracture cause of a rolling ring of a rotary kiln was studied through a stress analysis and some improvements were proposed.
通过对回转窑滚圈的应力分析，探讨了其断裂的原因，并提出了相应的改进措施。
On this base, the formula used for calculating the side pressure of ring wall, ring tensile and temperature contraction stress is established for engineering design.
在上述基础上提出的环墙侧压力、环拉力和温度收缩应力的计算公式，可供工程设计中采用。
Comparing the results of the welding residual stresses at outer surface of beryllium ring by FEM to that from X ray stress measurement, the stress trend is identical.
对铍环外表面钎缝附近焊接残余应力进行X射线应力测试，并与有限元分析结果对比，二者应力变化趋势基本一致。
The stress of the UP-attachment ring of the reactive kettle was measured by electricity.
用电测法对反应釜上接环处的应力进行了测定。
For MSCL and MHWH, the setting up of expansion joint and anti-thrust ring will not much affect the stress distributions of SC and surrounding concrete.
无论是对于垫层方案或是保压方案，是否设置伸缩节和止推环对蜗壳应力状态影响均较小。
A separated collecting ring with carbon brushes was designed and manufactured for the dynamic stress test of spoke plates of rotor of bulb tubular turbine generator.
根据测试需要，设计自制了分体式碳刷集流环，对灯泡贯流式水轮发电机转子辐板进行了动应力测试。
For the cylinder and ring specimens, raising thermal-cold transformation rate was not favorable for relaxing the residual stress.
对于圆柱和圆环试样，提高冷热转移速率不利于降低残余应力。
An experimental study of inlaid circular ring under impact force on interior boundary is also conducted. The result shows that the stress is distributed within a limited scope.
对内边界受冲击力作用的镶嵌圆环也进行了实验研究，结果表明，应力分布局限在有限范围内。
The residual stress of the beryllium ring weldment was studied by FEM simulation and X ray stress measurement.
采用有限元分析法和X射线应力测试法对铍环形焊件的残余应力分布规律进行了研究。
The impact load stress on the working process of the ring valve of reciprocating compressor is analyzed in this paper.
本文对往复式压缩机环状阀工作过程冲击应力进行了分析。
Thus, stress is transmitted not only through a side surface (58) but also through the reinforcing ring (40), between the adjacent divided cores.
由此，在邻接的分离铁心之间，不仅通过侧面58还通过加固环40来传递应力。
With the FEM simulation, the strain and stress of each node under different deformation stage are analyzed and the common forming law of this ring shell container is obtained.
采用有限元数值模拟对环壳零件成形过程中不同压下量下毛坯各节点的应力应变分布及变化规律进行了分析，获得了环壳零件冲压过程的成形规律。
The ring wall base resulted in sudden change of stress and formed steep subsidence zone at the ring wall on soft ground base, being unfavorable to stress at the bottom of the tank.
其次，当罐直径越来越大时， 混凝土环墙的温度应力和干缩成为设计难题。
By stress analysis, this article gives a calculation method on a spherical cap joining the flange ring by welding.
通过应力分析，给出了带法兰的无折边球形封头的计算方法。
The results show that the values of the initial tensile force have an important effect on the stress situations of concrete snail shell and ring base.
结果表明，锚索初始张拉力的大小对混凝土蜗壳及座环的应力状况有重要影响。
The results show that with the increase of the cone angles and the coefficients of friction in the certain range, the stress of the anchor ring can gradually decrease.
结果表明：随着锥角和摩擦系数在一定范围内增大，锚环的应力会逐渐减小；
In the direction of the existence of the outer ring gasket with high residual compression stress of the closed ring, the close of their joints have a crucial role.
在垫片的外环方向存在着具有较高残余压紧压力的闭合环带，它们对接头的紧密性有非常关键的作用。
Based on the elastic theory, the establishment of super-long tubes of ring pre-stress was studied.
基于弹性理论，对超长筒体结构中环向预应力的建立与分布进行了研究。
The temperature field and thermal deformation of the piston and ring carrier was used as the boundary in the calculation of stress field.
计算时把温度场和热变形作为结构应力计算的边界，获取活塞镶圈在热负荷状态下的综合应力场。
MARC software was used to simulate the temperature and stress fields of laser beam braze welding process of beryllium ring.
采用MARC软件对铍环激光束钎焊过程的温度场和应力场进行了有限元分析。
The resistance of nitrided J55 casing to sulfide stress cracking (SSC) was studied by C-ring testing and three-point bending testing under different conditions.
用应力环腐蚀试验和三(四)点弯曲试验研究了某J 55(即石油套管)渗氮套管在不同试验条件下的腐蚀行为，并和未渗氮套管的抗腐蚀性进行了比较。
It is assumed that the plate is in close contact with the ring without initial stresses. Stress functions of the plate and the ring are formed by a complex Laurent series.
假设板与环间处于无初应力的紧密接触状态，弹性板和弹性环的应力函数都可按复劳伦级数展开。
An experimental study of inlaid circular ring under impact force on interior boundary is also conducted. The result shows that the stress is distributed in a limited scope.
文中还对内边界受冲击力作用的镶嵌圆环进行了动光弹实验，结果表明，应力分布局限在有限范围内。
The temperature and stress fields of a ring structure laser welding are simulated by finite element method (FEM).
对铍环激光束钎焊过程的温度场和应力场进行了有限元模拟。
Combining practical matters, a method of the stress calculation of circular ring plates under press loading using flat circular plates formula was introduced.
本文结合实际问题，给出了利用《应力应变公式》中的等厚平圆板公式对受压环板应力的理论计算方法。
Combining practical matters, a method of the stress calculation of circular ring plates under press loading using flat circular plates formula was introduced.
本文结合实际问题，给出了利用《应力应变公式》中的等厚平圆板公式对受压环板应力的理论计算方法。
应用推荐