In this structure, the Gaussian mode could be transferred to the ring mode. So FEPCF could used as a mode convertor.
在这种结构中，高斯模可以转移到环形模，因此这种光纤可以作为一种模式转换器。
Kernel space is flagged in the page tables as exclusive to privileged code (ring 2 or lower), hence a page fault is triggered if user-mode programs try to touch it.
系统内核所使用的内存空间通过特权码（privileged code，2级或者更低）来标记，以防止用户模式的程序访问到内核空间而发生页面错误。
Based on these ideas, a wavelength assignment algorithm is presented. For an optical ring with any fixed conversion mode, the algorithm can give a good assignment scheme.
基于这些算法，进一步提出了一个波长分配算法，该算法对于环形光网上的任意固定转换模式都能给出一个较好的波长分配方案。
The effect of deformation mode and degree on the structure and properties of large conical ring forgings was analyzed. An optimal forging process was drawn up.
分析了变形方式和变形程度对大型锥环形锻件组织和性能的影响并制定较佳锻造工艺。
NTLDR then sets up the ring 0 mode for the kernel and loads the proper kernel (NTOSKRNL) for the computer.
然后NTLDR为内核设定0环模式，并为计算机装载正确的内核（NTOSKRNL）。
For example, before you go to sleep, set the bedside handset to Silent Mode so that it wont ring for the duration of your slumber.
例如，在你去睡觉，床边的手机设置为静音模式，所以它不会为你的睡眠时间环。
The ring output spot of the fundamental mode is obtained from a high gain TEA CO2 laser by experiment.
通过实验在高增益的TEA CO_2激光器中，得到了基模环形光斑输出。
The nonuniform wear is a popular failure mode of separating ring of heavy vehicle clutch.
表面非均匀磨损是重载车辆主离合器分离环常见的失效形式。
The influence of mode mismatch on measurement in continuous-wave cavity ring-down technology was theoretically analyzed and experimentally studied.
对连续波腔衰荡技术中的模式失配对测量结果的影响进行了理论分析和实验研究。
The material flow in steel synchronizer ring under top location mode is better than that under bottom location mode, which greatly benefits defects control.
对于钢质同步环，采用齿腔面定位方式下的材料流动状态明显优于齿根圆定位方式下的材料流动状态，有利于避免成形缺陷的产生。
In this paper, a thin ring plate mode is used, and more exact calculating formula is got for bending of the centrifuger vane.
本文采用环形薄板模型，得到关于卧螺离心机叶片弯曲问题的较为精确的计算公式。
The circumferential-direction vibration mode and axial vibration mode of the ceramic ring are discussed.
对圆管周向和轴向振动两种振动模式进行了讨论。
Kernel space is flagged in the page tables as exclusive to privileged code (ring 2 or lower), hence a page fault is triggered if user-mode programs try to touch it.
内核空间被标记在页表中的独家特权代码(环2或更低)，因此一个页面故障被触发，如果用户模式的程序试图去触摸它。
At this week's demonstration, the bots pursue the people in the ring, but when in "run away" mode, the tables get turned, and the robots flee from the people in the ring.
在本周的演示中，机器人追求的人在擂台上，但是当与私奔；模式，表得到转过身来，机器人与人在擂台逃跑。
The mode-sweep curve obtained by experiment shows that this power supply system can meet the requirement of automatic mode-sweep system of ring laser gyro.
实验获得的扫模曲线表明，该驱动电源能够满足环形激光陀螺扫模系统的要求。
This is the normal mode, the clock will ring at the time you set it to.
这是标准模式，时钟会在你设定的时间闹铃。
For example, before you go to sleep, set the bedside handset to Silent Mode so that it wont ring for the duration of your slumber.
例如，在你去睡觉，床边的手机设定为静音模式，所以它不会响了你的睡眠时间。
Electrical wavelength switching of an actively mode-locked, fiber Bragg grating incorporated fiber ring laser is demonstrated.
介绍了内置光纤光栅的主动锁模光纤环形激光器输出光脉冲波长电切换的工作原理和实验结果。
It includes electrolyte membrane, silicone rubber seal ring, multihole anode plate, and free lay mode formed granules of catalyst layer between said electrolyte membrane and multihole plate.
它包括电解质膜、硅橡胶密封圈、多孔阳极板，及在所述电解质膜和多孔板之间的自由铺放的方式形成的催化剂颗粒层。
Therefore it is necessary to investigate the influences of the facet residual reflectivity and the nonlinear polarization rotation on the characteristics of mode-locked ring lasers based on SOA.
因此，有必要对SOA的端面剩余反射率及非线性偏振旋转效应进行研究。
The simulation and design of single mode waveguide, curve waveguide, directional coupler and monobloc construction of passive ring resonator have been accomplished by using BPM software.
结合BPM软件，完成了对单模波导、弯曲波导部分、定向耦合器和无源环形谐振器整体结构的模拟和设计。
With the structure, the focusing ring can be quickly clamped on the optical mode lens; and assembly and disassembly are convenient and positioning is accurate.
由于本实用新型采用了上述结构，调焦环可快速地卡装在光模镜头上，拆装方便、定位准确。
With the structure, the focusing ring can be quickly clamped on the optical mode lens; and assembly and disassembly are convenient and positioning is accurate.
由于本实用新型采用了上述结构，调焦环可快速地卡装在光模镜头上，拆装方便、定位准确。
应用推荐