The rotational speed of the main roll of a profile ring mill is critical for insuring the success of its rolling process.
合理的主辊转速是保证异形环件顺利轧制的重要因素。
This paper introduces the operating principle of manufacturing complex surface in 5-axis nc machine. It is emphasis on error model of complex surface by ring mill cutter in 5-axis nc machining.
介绍了五轴数控机床加工复杂曲面的工作原理，重点分析了五轴数控加工时采用环形铣刀加工复杂曲面的误差模型，提出了误差补偿的具体方法。
Biomass pellet mill can be divided into flat die biomass pellet machine and ring die biomass pellet machine.
生物质颗粒机分为平模生物质颗粒机和环模生物质颗粒机。
The mill and its gearless drive is one of industry's largest installations (the ring motor is almost 20 meters high) and one of the pivotal applications in a concentrator plant.
研磨机及其无齿轮驱动器是该行业中最大型的设备之一(环行马达约20米高)，也是选矿厂的关键设备之一。
When the roller mill with a certain ring wear, the length of spring pressure adjusted to maintain a constant link between roller mill on the pressure roller.
当磨辊与磨环达到一定磨损后，调整高压弹簧长度，保持磨辊于磨环之间的恒定碾压力。
Coarse material entering the mill is crushed between the ring and rollers.
进入磨机的粗料压碎于辊和钢环之间。
The paper expounds the design idea of ring roll mill and structural design for raising the milling efficiency.
阐述了环磨机设计的思路及提高现有磨机的磨矿效率的方法、环磨机的结构设计。
The feed drive system of a precision cold ring rolling mill adopts AC servo motor and mechanical transmission, rather than conventional electro-hydraulic actuator.
采用交流伺服电机和机械驱动进给系统的冷轧环机，其进给伺服控制系统的设计需要一个新的工艺动力学模型。
An introduction is given to the configuration of the electric control system of a large scale radial-axial ring rolling mill and, meanwhile, its main functions and mutual relations.
介绍大型径轴向轧环机电气控制系统的结构与组成及各部分的主要功能和采用的相关技术。
An ultra-fine roll mill comprises a base, a host cylinder, a centre axle, a bracket, a grinding ring and a grinding roller device.
一种辊碾超细磨包括底座、主机筒体、中心轴、托架、磨环和磨辊装置。
Rotating ring die pellet mill is the key device of producing pellet feed, to a large extent determines the production of feed processing.
环模制粒机是饲料机械四大主机之一，很大程度上决定了饲料加工产量，在饲料加工过程中占有非常重要的地位。
Three rolling schedules were selected, dynamic simulations on the preloaded housing of cold ring rolling mill were proceeded with 3d finite element method, the results were compared.
选取3种轧制规程，用三维有限单元法对预紧机架进行了动力仿真，并进行了分析和比较。
The rolling experiment with lead as blank material is made in D51-160A hot ring rolling mill and the qualified pre-rolled ring of conical ring with inner steps is rolled.
采用铅环件试样在D51- 160A热轧环机上进行轧制实验，轧制出了合格的内台阶锥形环件预轧制环件。
The rolling experiment with lead as blank material is made in D51-160A hot ring rolling mill and the qualified pre-rolled ring of conical ring with inner steps is rolled.
采用铅环件试样在D51- 160A热轧环机上进行轧制实验，轧制出了合格的内台阶锥形环件预轧制环件。
应用推荐