Time delay filter is a new method to reduce residual vibration of flexible system.
时滞滤波器是一种消除柔性系统残留振动的有效方法。
Time delay filter technique is applied in the control of reducing residual vibration of a flexible beam.
将时滞滤波器技术应用在柔性机械臂残留振荡的控制中，获得了好的控制效果。
This paper calculates the residual vibration of rotors and axis with a new method equivalent dynamic stiffness factor.
提出用动刚度系数方法对转子和轴系残余振动进行预测。
The internal mechanism of time delay filter to reduce the residual vibration of flexible structures cannot be explained with the normal frequency characteristic.
常规频率特性无法解释时滞滤波器抑制柔性机构残留颤抖的内在本质。
Input shaping technique suppresses residual vibration through a open-looped input modulate method, therefore used widely in the high-accuracy fast navigation systems.
输入整形技术通过一种开环输入调制方法来抑制系统的残留振荡，因而在高精度快速定位系统中得到了广泛应用。
The simulation and experimental results show that not only the residual vibration but also the frequency of run-ups in the balancing process can be reduced effectively.
仿真和实验结果表明，该瞬态平衡方法在有效降低转子不平衡振动的同时，减少了平衡过程中的起车次数。
The residual vibration fatigue life of TC4 plate blade subjected to Foreign Object Damaged (FOD) is investigated by means of eddy current excited vibration fatigue tests.
采用电磁涡流激振的振动疲劳试验，对TC4材料制成的平板叶片受外物损伤后的剩余振动疲劳寿命进行了研究。
In the paper, the redundancy is used to decrease residual vibration of flexible link robot through optimal self motion, and the method is proved to be efficient by computer simulation.
本文将冗余自由度用于消减柔性杆机器人的残余振动，通过优化选择最优的自身运动以达到减振目的，模拟结果表明，这一方法可以取得很好的效果。
For each discretized angular speed, the control law is derived from the generalized linear quadratic objective performance function including residual vibration measurements and imbalance correction.
针对每个离散角速度，依据影响系数法，采用包含残余振动值和校正不平衡的广义线性二次型目标性能函数推导出控制律。
At present, temper aging and vibration aging (VSR) are commonly applied to remove residual stress in welded frames in factories.
目前，工厂中一般采用回火时效和振动时效法(VSR)对焊接构架中的残余应力进行消除。
The relationship between magneto-vibration and magnetic treatment induced tensile residual stress reduction in the steel 45 was studied.
研究了45钢脉冲磁处理过程中残余拉应力与磁致振动之间的相互作用关系。
Numerical results show that the sliding vibration isolation structure using semi-active control not only has good isolation effect, but also has lesser maximum slippage and residual base displacement.
对计算实例的分析表明，通过半主动控制的滑移隔震结构不但具有较好的隔震效果，且能有效地减小基底的最大滑移量及残余位移。
The influences of the welding residual deflections and stresses on the plating vibration were discussed.
探讨了焊接残余变形、残余应力对船体板振动频率的影响。
A closed-loop input shaping control scheme, which combines an input shaper with a vibration damper, is proposed for suppressing the residual oscillations of the multi-mode flexible systems.
提出一种闭环输入整形控制方案，它结合了具有振动阻尼器的输入整形器，用于抑制残留的多模式的灵活的系统振荡。
The method comprises the following steps: residual stress in a workpiece is measured, and dynamic stress level applied during vibration stress relief for the workpiece is determined;
该方法为：测量工件内残余应力，并确定对工件进行振动时效处理时应施加的动应力水平；
Numerical results show that the sliding structure using semi-active control not only has good vibration isolation effect, but also has less maximum slippage and less residual base displacement.
对实例计算结果的分析表明，半主动控制下的滑移隔震结构不但具有较好的隔震效果，而且能有效地减小基底的最大滑移量及残馀位移。
Secondly the principle of vibration time effect is elaborated. The reasons of producing residual stress and its influences on mechanical workpieces are analyzed.
其次对振动时效的原理进行了详细的阐述，分析了残余应力产生的原因及对机械工件的影响。
Secondly the principle of vibration time effect is elaborated. The reasons of producing residual stress and its influences on mechanical workpieces are analyzed.
其次对振动时效的原理进行了详细的阐述，分析了残余应力产生的原因及对机械工件的影响。
应用推荐