The relay circuit is just an example.
中继电路只是一个例子。
The relay circuit base board is arranged on the first chip.
中继线路基板配置于第一芯片上。
A new relay circuit automation design system was introduced in this paper.
本文介绍了一种全新的继电线路自动化设计系统。
These functions and advantages are hardly implemented by common relay circuit.
这些功能都是一般继电器控制线路难以达到的。
Automation design of relay circuit is a practical problem which is needed to be solved urgently.
继电线路的自动化设计成为一个迫切需要解决的实际问题。
This device consists of self-coupling transfer, digital logic circuit and low voltage relay circuit.
它由自耦变压器、数字逻辑电路和低压小继电器电路组成。
The second bonding wire is electrically connected between the relay circuit base board and the loader.
第二焊线电性连接于中继线路基板与承载器之间。
The first bonding wire is electrically connected between the first chip and the relay circuit base board.
第一焊线电性连接第一芯片与中继线路基板之间。
That is, when the line failure, the relay circuit breaker tripping, the device auto-reclosing after a short time interval, so that a re-breaker.
即当线路出现故障，继电保护使断路器跳闸后，自动重合闸装置经短时间间隔后使断路器重新合上。
Relay system is one of the most broadly used control systems. Relay circuit is the basis of relay system and it is also the main task of the design.
继电控制系统是应用最为广泛的控制系统之一，继电线路是继电控制系统的基础，是设计的主要任务。
Design the CAN bus address encoder, communication terminal digital display circuit, control relay circuit, LNK501 switching power supply chip circuitry.
设计了基于CAN总线的地址编码器，通信总站的数码显示电路，控制继电器电路，LNK501开关电源芯片电路。
Jitter, that is very likely damage degaussed resistance, in the absence of sound may be the relay and control circuit problem.
抖动，说明极有可能是消磁电阻损坏，如果没有响声则可能继电器及其控制电路有问题。
Depending on the application, these can alter the performance of the circuit in which the relay is used.
根据应用的不同，这些都会改变使用继电器的电路的性能。
Use relays, contactor, button, air switch and travel switch etc low-voltage constitute control circuit called relay contact control circuit.
使用继电器、接触器、按钮、空气开关、行程开关等低压电器构成的控制电路称为继电接触控制电路。
When the relay operates, one or more contacts will operate and energize a trip coil in a Circuit Breaker and trip (open) the Circuit Breaker.
当继电器动作时，一个或多个接触器动作且给断路器的脱扣线圈通电，从而将断路器断开。
Settling Time—This is the time required for the circuit to stabilize once the relay has been closed.
稳定时间——是指继电器关闭后电路达到稳定所需的时间。
Often in ac circuit by air damping model time relay, it is to use the principle of air through orifices throttling to obtain delay action.
在交流电路中常采用空气阻尼型时间继电器，它是利用空气通过小孔节流的原理来获得延时动作的。
The low-voltage relay and the excess voltage relay are integrated into one relay, which can display the real time of the voltage of the circuit and the limit of voltage can be modified.
该继电器的设计思想是将过压继电器和欠压继电器集成到一起，并且实时显示所测电压值，能修改电压的上、下限。
Testing data is received with data acquisition plug, signal from tested circuit board is transferred by circuit of switch relay.
前端采集插头接收测试数据，切换继电器电路传递被测电路板信号。
The intermittent control of wipers is related to the control switch, control relay and its control mode of the wipers operating circuit.
刮水器间歇控制与刮水器控制开关、刮水间歇控制继电器及其在刮水器工作电路中的控制方式有关。
Early in the circuit often USES air damping model time relay, it is to use the principle of air through orifices throttling to obtain delay action.
早期在交流电路中常采用空气阻尼型时间继电器，它是利用空气通过小孔节流的原理来获得延时动作的。
The article analyses control circuit of relay contactor in electric circuit experiment and puts forward to control it with logic function.
对电路实验中继电接触器控制线路进行了研究分析，并提出由逻辑函数实现其控制的方法。
This paper introduces the portable protection relay detecting device and the practical circuit, as well as the major functions.
介绍一种便携式保护继电器测试装置的设计及实用电路和主要功能。
Previously, a typical protection circuit would include a relay, resettable fuse and MOV combination to protect against the above combination of threats.
以往来说，典型电路保护将继电器、可恢复式保险丝、与金属氧化物压敏电阻组合来保护防止损害。
Temperature computer control system of a resistance furnace is designed with industry person computer (IPC), temperature input module, PWM output card, solid state relay(SSR) and interrelated circuit.
设计和实现了一种采用工控机与温度模块、PWM输出卡、固态继电器及相关控制电路搭建的计算机电阻炉温度控制系统。
The effects of PT secondary circuit on relay protection and measurement were analyzed by an example and the improving measures were set forward.
引用实例分析了PT二次回路对继电保护和计量的影响，并提出了改进措施。
Introduction was made to the composition and working principle of a power-off time delay relay which adopts CMOS digital circuit, digital dial disc for switch setting and without auxiliary power.
介绍了一种采用CMOS数字电路、数字拨盘开关整定、无辅助电源的断电延时继电器的组成及工作原理。
A method in the improvement of current relay controls winding asynchronous motor starting circuit is put forward, and the merit, demerit of it are described in the paper.
本文提出电流继电器控制绕线式异步电动机起动电路改进方法，并对改进电路优劣进行了分析。
This paper introduces a new AC voltage adjustment device controlling by optocoupler relay and gives detailed analysis of it's circuit.
对一种用光耦合继电器控制的交流调压器进行了介绍和分析，给出了该调压器的特点。
It is described in this paper that how to use two-position relay to solve simulation design of contact of CB in control circuit of simulation substation.
介绍在仿真变电站断路器控制回路仿真设计中，如何利用双位置继电器解决断路器机构触点仿真设计的问题。
应用推荐