This queue manager should be located on another node.
此队列管理器应位于另一个节点上。
Standardize on nodes and node separators in queue names.
标准化队列名称中的节点和节点分隔符。
Notice that the profile matches a queue named ABC.. JKL because it has three nodes, even though the middle node has no characters.
注意，配置文件将匹配一个名称为abc. . JKL的队列，因为它有三个节点，即使中间的节点没有字符。
Stop the queue manager on the backup node.
停止备份节点上的队列管理器。
If any remote node in the cluster is authorized to a queue, then all nodes in the cluster can send messages there.
如果某个集群中的任一远程节点被授权到一个队列，则该集群中的所有节点都能够将消息发送到那个队列。
In addition, applications connected to the partial repository queue managers need to put messages to clustered queues which might be hosted on some other node.
此外，连接到部分储存库队列管理器的应用程序需要将消息放到集群队列中，集群队列可能驻留在其他节点上。
In this case, a queue manager alias is typically used to achieve node equivalence, but the overall effect is still that the queue is resolved in the context of its queue manager.
在此情况下，通常使用队列管理器别名来实现节点等效性，但是总体效果仍然是在其队列管器的上下文中解析队列。
The vulnerability here is that a spoke node can address messages not to the input queue at the hub, but rather to the output queue at the hub.
这里的漏洞在于，分支节点可以不将消息发送到中心的输入队列，而是发送到中心的输出队列。
Like many queue algorithms, an empty queue consists of a single dummy node.
像许多队列算法一样，空队列只包含一个假节点。
MQ clustering will provide load balancing for all of the inbound events, and the JMS adapter and queue manager will fail over as a pair to the passive node in the availability cluster.
MQ集群将为所有入站事件提供负载平衡，JMS适配器和队列管理器将故障成对转移到可用集群的被动节点。
Multiple queue managers on one node: In some cases, completely separate queue managers are required.
一个节点上的多个队列管理器：在某些情况下，需要完全单独的队列管理器。
There is the potential to compromise the integrity of the queue manager (for example, with a badly written plug-in node).
存在损害队列管理器的完整性的可能（例如，错误编写的插件节点）。
On the backup node (ha2), create the queue manager as user MQM.
在备份节点(ha2)上，以用户mqm身份创建队列管理器。
Do not run halinkmqm on the node on which you created the queue manager with hacrtmqm — it has already been run there.
不要在使用hacrtmqm创建队列管理器的节点上运行halinkmqm—它已经在那里运行了。
One way to save the ReplyIdentifier between flows is to store the value on a queue, then use an MQGet node in the reply flow to retrieve it.
在流之间保存ReplyIdentifier的一种方法是将该值存储在队列上，然后在应答流中使用MQGet节点来检索该值。
Each broker instance is embedded into a WebSphere MQ service so that, when the queue manager switches over to the standby system, the broker is automatically started on the standby node.
每个代理实例都嵌入到一个WebSphereMQ服务中，以便当队列管理器切换到备用系统时，代理自动在备用节点上启动。
On the primary node (ha1) create a highly available queue manager using the command shown below (as root).
在主节点(ha1)上使用下面的命令创建一个高可用的队列管理器(以root身份)。
Finally, the MQOutput node writes an output message to a queue named LENGTH.OUT.
最后，MQOutput节点将输出消息写入到名为LENGTH.OUT 的队列中。
Figure 3 illustrates the input flow, which USES an MQInput node to read MQ messages from an MQ queue.
图3演示了该输入流，其中使用了MQInput节点来从mq队列读取MQ消息。
In configurations where the MQ queue manager is running on the same node as WebSphere Application Server, using bindings mode offers a performance advantage.
在mq队列管理器与WebSphereApplicationServer运行于同一节点的配置中，使用绑定模式可提供性能优势。
This pattern uses a message flow shown below in Figure 19, which receives data over TCP/IP, parses it using a WebSphere TX node, and writes it to a WebSphere MQ queue.
该模式采用图19所示的消息流，通过TCP/IP接收数据，使用WebSphereTX节点进行解析，然后将数据写入到 WebSphereMQ 队列。
Click the node and specify in for the Queue name property for the node in Properties TAB's Basic folder.
单击该节点并在Properties选项卡的Basic文件夹中指定in作为该节点的Queuename属性。
The complete employee information is propagated to the EMP_OUT Output node, which puts the message to the EMP_OUT queue.
完成的员工信息被传播到EMP_OUT OUT put节点，该节点将消息放在EMP_OUT队列中。
Start the queue manager, ha.queue.manager, using the strmqm command, on the backup node.
在备份节点上，使用strmqm命令启动队列管理器 ha.queue.manager。
A node running a queue manager must also maintain a number of files on internal disks.
运行队列管理器的节点还必须在内部磁盘上维持许多文件。
We also analyzed the average queue delay of MAC layer by modeling the interface queue of each node with M/D/1 model.
然后用M/D/1排队模型对每个节点的MAC层队列建模，分析了MAC层队列的平均排队延迟。
It expatiates the implement method in detail, which involves the data communication state machine between gateway and Infra - red node, timer design and the management of data queue.
详细说明了红外网关的具体实现方法。其中包括网关与红外接收器的数据通信状态机、定时器设计以及数据队列管理。
The core of this model is to make the queue length of node proportional to ( is the degree of node and is an allocation parameter).
模型的核心是使节点的队列长度与成正比（为节点的度，为分配参数）。
In the Node properties section under the Basic TAB, input Q.IN as the Queue name and leave the rest of the field as default.
在Basic选项卡之下的node属性部分输入Q.I N作为queue名，并使其余字段保留默认设置。
In the Node properties under the Basic TAB, enter MYQM for the Queue manager name properties and Q.OUT for the Queue name properties.
在Basic选项卡之下的node属性中，输入Queuemanagername属性MY QM，输入Queue name属性q.o UT。
应用推荐