QLogic driver, version qla2xxx 8.01.07.15
QLogic驱动程序，版本为qla2xxx 8.01.07.15
These are also known as Qlogic 2342 adapters.
它也称为Qlogic 2342适配器。
At this stage, you need to set up the boot device in the Qlogic BIOS.
在该阶段，您需要在QlogicBIOS中设置根设备。
The example cluster USES the Qlogic qla2300 driver, version 7.01.01, for the Qlogic qla 2342 adapters.
示例集群使用的是Qlogicqla2300驱动程序，版本为7.01.01，用于Qlogicqla 2342适配器。
The disk-storage system is connected to the host system with four QLogic QLA2342 Fiber Channel adapters.
磁盘存储系统通过四个QLogicQLA2342光纤通道适配器连接到主机系统上。
In this case, put all other SCSI adapters drivers (like the Qlogic HBA driver qla2xxx.ko) after the sas adapter driver mptsas.ko.
在本例中，将所有其他SCS i适配器驱动程序(如qlogicHBA驱动程序qla2xxx . ko)放在sas适配器驱动程序mptsas . ko之后。
These include the installation of the GPFS code on each node and the configuration of the Qlogic adapters for the storage nodes.
内容包括在每个节点上安装GPFS代码，以及为存储节点配置Qlogic适配器。
MSJ is used for configuration of the Qlogic adapters, failover, and multipathing, which is described in detail under HBA configuration.
MSJ用于Qlogic适配器、故障恢复和多路径等配置，这将在HBA 配置 一节中详细进行介绍。
The disk configuration is a mix of IBM EXP arrays attached to a SCSI controller, and a FAStT 600 system connected to the server via two QLogic fiber cards.
磁盘配置采用了一个IBMEXP阵列，连接到一个SCSI控制器上；一个FAStT 600系统，通过两个QLogic 的光纤卡连接到服务器上。
The disk configuration is a mix of IBM EXP arrays attached to a SCSI controller and a FAStT 600 system, connected to the server via two QLogic fiber CARDS.
磁盘配置是混合的IBMexp阵列，附到一个SCSI控制器和一个FAStT 600系统上，通过两个QLogic光纤卡连接到服务器。
First, you need press Ctrl-Q to select the Host Adapter page when your server posts the Qlogic self-test. You should get something like you see in Figure 9.
首先，您在服务器发布Qlogic自检时需要按下Ctrl - Q选择HostAdapter页面，如图9所示。
This problem affects the storage nodes where, if PXE boot is enabled, there is not sufficient space for the Qlogic PCI adapters to initialize properly. One work around to this is the following.
如果启用了PXE引导，这个问题就会影响存储节点，其中Q logicPC i适配器没有足够的空间正确进行初始化。
This problem affects the storage nodes where, if PXE boot is enabled, there is not sufficient space for the Qlogic PCI adapters to initialize properly. One work around to this is the following.
如果启用了PXE引导，这个问题就会影响存储节点，其中Q logicPC i适配器没有足够的空间正确进行初始化。
应用推荐