Spring-actuated valve to be used on pump discharge.
弹簧执行机构止回阀用于管道排放。
Ctc maximum head is suitable for pump discharge to butanol handling facility.
用户确认泵出口去丁醇处理装置的最大扬程是合适的。
Reciprocating pump discharge pipe must be before the start of the valve to open.
往复泵启动前必须将排出管路中的阀门打开。
Low pump discharge pressure during pump operation shall sound an alarm and be indicated on the HMI.
低泵泵运行期间的排放压力应发出警报声，并在HMI上显示。
In order to prevent damage to the pump must pump discharge pipe into the suction pipe installed between the safety valve.
为了防止泵的损坏，必须在泵的排出管到吸入管之间安装安全阀。
On pump discharge, the preferred check valves are in-line spring loaded, swing design with lever and weight or lever and spring.
在泵出口处，首选止回阀是管内弹簧负载，配置杠杆和重量旋启式结构，或杠杆和弹簧旋启式结构。
NOTE: On pump discharge, the preferred check valves are in-line spring loaded, swing design with lever and weight or lever and spring.
注意：在泵出口处，首选止回阀是管内弹簧负载，配置杠杆和重量旋启式结构，或杠杆和弹簧旋启式结构。
The level of suction pumps for the axial direction, pump discharge outlet may be fitted into the needed horizontal or vertical direction.
泵吸入口为轴向水平方向，泵排出口可根据需要装成水平或垂直方向。
Note: On pump discharge, the preferred check valves are an in-line spring loaded, swing design with lever and weight or lever and spring.
注意：在泵排泄口，首选的止回阀是管内弹簧负载，带杠杆和压铁或杠杆和弹簧的旋启式止回阀。
NOTE: On pump discharge, the preferred check valves are an in-line spring loaded, swing design with lever and weight or lever and spring.
注意：在泵的排泄口处，首选的止回阀是管内弹簧负载，旋启式，配置杠杆和重量或杠杆和弹簧。
Note: on pump discharge, the preferred check valves are an in - line spring loaded, swing design with lever and weight or lever and spring.
注意：在泵的排泄口处，首选的止回阀是管内弹簧负载，旋启式，配置杠杆和重量或杠杆和弹簧。
Spring-actuated valve to be used on pump discharge. Swing check with outside lever and spring to be used on sump, sewage and storm drain lines.
弹簧执行机构止回阀用于管道排放。外置操作手柄和弹簧执行机构的旋启式止回阀用于污水坑、排污和雨水排泄管道。
When we don t operate the multiple directional value handle, the hydraulic oil that pump discharge back to oil box by multiple directional value.
在不操作多路换向阀手柄时，油泵排出的液压油经多路换向阀回到油箱。
Install 5 pipe diameters minimum downstream from pump discharge or elbows to avoid flow turbulence. Flow straighteners may be required in extreme cases.
安装位置距泵出口或弯管下游处最少应该有5倍管道直径的长度的位置。极端情况下可能需要安装流向矫直装置。
The pump discharge of Jiangdu second pump station of the South-North Water Project was made and the uncertainty of the measurement results was analyzed.
因此，研究水泵流量尤其是低扬程大流量泵站的水泵流量测量是十分有意义的。
Press out the liquid at this time to overcome the pressure out of pipeline systems with all the necessary resistance to the pressure from the pump discharge.
压出，此时液体带有克服压出管道系统所有阻力所必需的压力从泵中排出。
Pump discharge of oil with reasonable design, gear oil and back at work under minimum torque force bearing load, so small, wear small, pump with high efficiency.
泵内有设计合理的泄油和回油槽，是齿轮在工作中承受的扭矩力最小，因此轴承负荷小，磨损小，泵效率高。
The whole test stand is mainly made of pump stage part, intake part, discharge part and data acquisition part.
整个试验台架由泵级部分、吸入部分、排出部分和数据采集部分组成。
Do not let pump run for long in the circumstance of discharge valve closed.
注意不要在排出阀关闭的状态下长期运转。
The pump casing shall be suitably ribbed have tangential discharge and be reinforced to support the weight of the motor assembly.
泵壳应该有适当的肋骨，按切线方向排放，能够再加固以支撑电机总成的重量。
The pump casing shall be suitably ribbed, have tangential discharge, and be reinforced to support the weight of the motor assembly.
泵壳应该有适当的肋骨，按切线方向排放，能够再加固以支撑电机总成的重量。
When the pump is going to stop, first press the stop button (Red), then close the water intake valves and the discharge valve.
停泵时先按下电控箱上泵的停止按钮(红色)，泵停止运转后，关闭管路上的进水阀和排出阀。
The pump casing shall be suitably ribbed have tangent ial discharge and be reinforced to support the weight of the motor assembly.
泵壳应该有适当的肋骨，按切线方向排放，能够再加固以支撑电机总成的重量。
TUPWR algorithm was adopted for the pump turbine model, SFPUMP for feed pump system, SOVLV for minimal flow valve, and pressure node for calculating the discharge rate of the pump.
给水泵汽轮机模型采用TUPWR算法，给水泵系统采用SFPUMP算法，最小流量阀采用SOVLV算法，泵出口流量的关系采用压力节点进行计算。
The discharge elbow shall be designed to carry the full weight of the pump, motor and discharge piping.
排泄弯头设计结构应该能够承受泵、电机和排泄管道的全部压力。
This set of components can rotate to the back leakage discharge hole and pump the bottom of the alignment.
这样可以使整套部件旋转至背板漏液排出孔与泵的最底端对齐。
Double screw pump as a positive displacement pump, the pump suction chamber should be closely separated and discharge chamber inside.
双螺杆泵作为一种容积式泵，泵内吸入室应与排出室严密地隔开。
The sludge is passed under a vacuum pump and allows the water to pass through a discharge or recirculation drain.
用真空泵除去污泥的固体含量而该泥水则经排水渠或回流渠排出。
The addendum coefficient is an important parameter in the designing the gear, and to affect the discharge characteristic of compound gear pump.
齿顶高系数是设计齿轮时的重要几何参数，也是影响复合齿轮泵流量特性的重要参数之一。
The addendum coefficient is an important parameter in the designing the gear, and to affect the discharge characteristic of compound gear pump.
齿顶高系数是设计齿轮时的重要几何参数，也是影响复合齿轮泵流量特性的重要参数之一。
应用推荐