The paper introduces the work principle, technique requirement and control system for Capacitor pulsed welding, which is used MELSEC series PLC for control system.
介绍了电容储能焊接的工作原理、工艺要求和控制系统，并用三菱公司PLC实现其系统控制。
So research on the Pulsed MIG welding power source becomes more and more important.
因此对脉冲mig焊接电源的研究具有很大的实际意义。
The plasma cloud charge sensor was applied to detect the status of keyhole molten pool during pulsed plasma arc welding, furthermore, the detected signals were studied.
将等离子云传感器应用于脉冲等离子弧焊穿孔熔池小孔状态检测，并对检测信号的波形特征做了深入研究。
In the paper, Pulsed MIG welding power source system is designed based on DSP.
论文建立了基于DSP的数字化脉冲m IG焊接电源系统。
Methods: Electrochemical technique was adopted to detect the changes of anode polarization curves of TA2 and TC4 after welding with laser or pulsed tungsten argon arc.
方法：采用动电位极化技术，分别测定激光焊接及脉冲氩弧焊接TA2和TC4后，材料阳极极化曲线的变化。
According to the arc light features of pulsed TIG welding and its effects on vision measurements, a special method of image capturing and controlling is put forward.
根据脉冲tig焊接电弧的弧光特性及其对视觉检测的影响，提出了一种独特的图象采集和控制方法。
The main purpose of studying welding technology AC pulsed MIG is used to weld splint.
研究交流脉冲MIG焊接工艺的主要目的是为了焊接薄板。
The self-adaptation control of dynamic characteristics of pulsed MIG welding was achieved by a short circuit controller and a dynamic electronic inductor.
采用短路电流控制器和动态电子电抗器，实现了脉冲MIG焊动态特性的自适应控制。
In this paper, the control system of IGBT inverter power source with microcomputer control for pulsed MIG welding is introduced.
介绍了自行设计开发的微机控制的脉冲MIG焊电源控制系统。
In this paper, a variable model of optimum droplet transfer mode for pulsed GMA welding using a steel electrode is developed on the principle of the micro-interference instability of magnetofluid.
前言：基于磁流体微扰动“失稳”的原理，建立了钢焊丝脉冲GMA焊最佳熔滴过渡形式的参数模型。
And it enumerates the troubleshootings in WSE-500 multi-function pulsed tungsten argon arc welding.
例举了WSE- 500多功能脉冲钨极氩弧焊机故障排除的事例。
The result of developing microcomputer control system of pulsed MIG welding is introduced in this paper. The component parts and control principle of the system are analyzed.
介绍了脉冲MIG焊微机控制系统的研制成果，分析了该系统的组成和控制原理。
For multilayer welding on steel, pulsed arc welding is recommended-also appropriate for oven soldering.
建议在钢材多层焊时使用脉冲电弧焊，也适合于炉焊。
Metal Doctor (MD) is a pulsed micro-welding process that is being used increasingly for small scale and precision coating and repair of high value components.
金属医生是一种脉冲微弧焊接过程，可以用来在小面积范围内实现精密涂层和用来修复高附加值的部件。
Based on the metal melt and vaporized interface 2d propagation mechanism, this paper founds the pulsed laser welding model.
基于金属材料熔化、汽化界面二维扩展机制建立了脉冲激光的焊接模型。
The hardware circuit and software program features of the given current, multi-pulsed resistance welding machine controller developed 8031 single chip processor are introduced in this paper.
本文介绍了用8031单片机研制的定电流，多脉冲电阻焊机控制器的硬件电路及软件程序的特点。
Finally, the technologic experiment of twin-wire welding was done with the equipment of twin-wire pulsed MAG high speed welding power supply and its multi-phase digital synchronic control system.
应用所研制的双丝脉冲mag高速焊多相位数字化协同控制电源装备进行了大量的双丝高速焊工艺试验。
The qualitative analysis is carried out on the behavior of the partial penetrated weld pool with welding current changing from pulsed peak value to base value during pulsed TIG welding.
对脉冲TIG焊未熔透型熔池在脉冲峰-基转换期间熔池三维形态变化行为进行了定性的分析，并从力和能量角度建立了未熔透熔池液面形态的数学模型。
A new type of argon tungsten pulsed arc welding machine has been introduced in this paper.
本文介绍一种新型钨极脉冲氩弧焊机，分析了基本工作原理及技术性能。
A microcomputer controlled IGBT inverter power source for pulsed MIG welding is developed. It realizes the self adaptive control and closed loop control of arc voltage in pulsed MIG welding process.
建立了微机控制和IGBT逆变式脉冲MIG焊电源系统，实现了MIG焊接过程弧压自适应闭环控制。
A new type of argon tungsten pulsed arc welding machine has been introduced in this paper. The basic operating principle and technical characteristics has been analyzed.
本文介绍一种新型钨极脉冲氩弧焊机，分析了基本工作原理及技术性能。
Pulsed arc welding power source by thyristor DC chopper consists of common DC arc welding power source and DC chopper.
采用晶闸管直流斩波器的脉冲弧焊电源是由普通的直流弧焊电源，附加晶闸管直流斩波器组成的。
With the wide application of aluminum alloy to transportation and aircraft, it has become more and more popular for the use of robotic pulsed-MIG welding for aluminum alloy.
随着铝合金在交通运输、航空航天等行业的广泛应用，铝合金机器人MIG焊技术在这些领域的应用日趋普遍。
Particularly suitable for repair welding of bronze statues. For multilayer welding on steels, pulsed arc welding is recommended. For large work pieces preheating is recommended.
特别适合铜雕像修复的焊接，建议在钢材多层焊时使用脉冲电弧焊，用于大焊件时建议预热。
For multilayer welding on steels, pulsed arc welding is recommended.
在多层钢加层焊时建议使用脉冲电弧焊。
Impact of welding parameters on the meso-spray transfer in Al pulsed-MIG welding has been studied in the Al pulsed-MIG welding experiment based on meso-spray transfer self-adapting control.
运用亚射流过渡自适应控制思想进行了铝脉冲MIG焊工艺试验，研究了焊接参数对铝脉冲MIG焊亚射流过渡的影响。
Study on the pulsed feeding wire system for underwater welding;
利用混沌理论对水下目标特征提取进行了研究。
Study on the pulsed feeding wire system for underwater welding;
利用混沌理论对水下目标特征提取进行了研究。
应用推荐