The next two statements set the proxy host and proxy port to connect to the Internet.
下面两个语句设置连接到Internet的代理主机和代理端口。
Proxy Settings: if you access the Internet via a proxy server, you will need to specify your proxy address and proxy port number.
ProxySettings：如果通过代理服务器访问Internet，则将需要指定代理地址和代理端口号。
This is caused by the lack of HTTP traffic being routed through the network proxy recorder on local host port 1080.
这是由于缺少HTTP地址流量造成的，这个地址流量是通过网络代理记录器在本地主机端口1080按照线路发送的。
This line sets an HTTP proxy for the SOAP client, pointing it to port 8888 on the local machine.
这一行为SOAP请求设置了一个HTTP代理，将其指向本地机器的端口8888。
The dynamic proxy creates the proxy at runtime and, therefore, provides the flexibility to bind to specific port and endpoint.
动态代理在运行时创建代理，从而可灵活绑定到特定端口和端点。
Enable the reverse proxy server to listen on ports 80, 443, 8000, 8002, and 8004 by adding one listen directive for each port as follows.
为每个端口添加一个Listen指令，以使该反向代理服务器在端口80、443、8000、8002和8004上进行侦听，如下所示。
For both HTTP Proxy and SSL Proxy, type localhost, and set the port to 8008.
对于HTTPProxy和SSL Proxy，都输入localhost，并将端口设置为8008。
Enter any port, timeout, or proxy Settings for the test, and then select Next.
为测试输入任意端口、超时时间，或代理设置，并选择Next。
The web service proxy configuration for this example has a HTTP front end configured for the desired port.
此示例的Web服务代理配置具有配置为使用所需端口的HTTP前端。
Check the Enable proxy check box and enter the proxy host name and port (the same values you'd specify in a Web browser to access the Internet).
选中enableproxy复选框，并输入代理主机名称与端口(您在Web浏览器中访问Internet时所指定的相同值)。
Once the application is started, the proxy will detect that the application and port are available and will route traffic as appropriate.
启动应用程序后，代理将检测可用的应用程序和端口，并对通信流进行恰当的路由。
Only the proxy can connect to the actual Web server through port 2001.
只有代理才能通过端口2001连接到实际的Web服务器。
To run Paros, you must change the port number used in the proxy settings of your browser.
要运行Paros，必须更改浏览器代理设置中使用的端口号。
Add proxy and port properties, as shown in Figure 28.
我们要添加proxy和port属性，如图28所示。
When the Web application starts, it displays a message saying "MyPlugin starting" and sets the system's proxy and port.
当启动Web应用程序时，会显示一条消息说“MyPlugin starting”，并设置系统的proxy 和 port 属性。
For HTTP and Secure, type localhost for the proxy address to use, then type 8008 for the port.
对于HTTP和Secure，在proxyaddresstouse下输入localhost，然后在port下输入8008。
It can scan proxy servers in special IP and port ranges as well.
该软件可以扫描特定ip地址和端口范围的代理服务器。
Use to complete the port write simple the HTTP PROXY procedures, suitable for beginners learning to complete the port and HTTP proxy!
说明：使用完成端口编写的简单HTTPPROXY程序，适合学习完成端口和HTTP代理的初学者使用！
The proxy server port in a run an HTTP proxy.
这个代理服务器在某一端口运行一个HTTP代理。
The application supports dynamic tunneling via proxy, so you can steer your applications to a desired port.
该应用程序支持动态隧道通过代理服务器，使您可以领导您的应用程序所需的端口。
Since each HTTP access services resource can be configured to send traffic to a different back-end server or proxy, configure each service to listen on a different port.
由于每个HTTP访问服务资源可配置为将传输发送到不同的后端服务器或代理，因此可以配置每个服务，以侦听不同的端口。
List of hosts without proxy: (host: port,...)
没有代理的主机列表：(主机：端口，…)。
If a message goes through a relay or proxy, the IP address and port number of the respective relay or proxy is the one attached to the message by this property.
如果消息经过中继或代理，则相应中继或代理的IP地址和端口号是此属性附加到消息中的IP地址和端口号。
Type the port number used by the proxy host for proxy requests.
输入代理主机代理用的端口号。
Type the port number used by the proxy host for proxy requests.
输入代理主机代理用的端口号。
应用推荐