Program instruction set, logic stack and data type of I/O memory which are tied up with tasks in the soft-PLC system are analyzed and studied.
研究了系统的程序指令集、逻辑堆栈和I/O存储器数据类型，实验表明系统具有良好的实时性和可靠性。
Its successor was the 4040 processor (released in 1974), which had an expanded instruction set, program memory, register set, and stack.
其后面是4040处理器(1974发布)，其具有扩展指令集、程序内存、寄存器集和堆栈。
A compound statement consists of a flow control instruction, followed by a colon character (:), followed by a block of program statements.
一个复合语句包括一个流控制指令，后跟一个冒号(：)，然后再是一个程序语句块。
It stores the instruction, the logical program order of instructions, and the completion order of instructions in the group.
它存储指令、指令的逻辑程序次序和指令在组中的完成次序。
A higher CPI value indicates that more cycles were necessary to run the instruction, implying suboptimal execution of the program.
cpi值越高，则运行指令所需的周期就越多，这意味着程序的运行性能未达到最优。
A tiny program can clear all of memory. A single instruction can stop the machine.
比如，一段小程序可以抹去所有的内存；一条简单的指令可以使主机停止运行。
A base of biology, chemistry, and math courses are advised, and program coursework will include clinical, laboratory, and classroom instruction.
建议要有生物学、化学和数学基础，拟定的培训课程包括临床、实验室和课堂教学。
The program in Listing 7 will try to execute an instruction that will move the value of an MSR to a GPR.
清单7中的程序会试图执行一条将一个值从MSR移动到GPR的指令。
In this program, it takes four clock cycles for instruction 1 to finish.
在这个程序中，完成指令1需要花费4个时钟周期。
A program references storage using the effective address computed by the processor when it executes a storage Access or Branch instruction or when it fetches the next sequential instruction.
在程序执行StorageAccess或Branch指令或者在存取下一条顺序指令时，它将使用处理器计算出的有效地址引用存储设备。
Each line of the program contains a single instruction. It could bewritten in English like this.
程序的每一行都是一条单独的指令。
Of course, it cancels the program-quit instruction.
当然，它取消的是程序退出指令。
What the program will end up doing is calculating both answers, and then using a conditional instruction to select the desired answer.
这个程序最终要做的是计算两种答案，然后使用一个条件指令来选择所需要的答案。
That program counter points to some location in memory typically to the first instruction in the sequence.
程序计数器指示存储器当中的某些位置，尤其是指示序列中的第一个指令。
A traditional computer which executes program according to the instruction sequence set by instruction counter.
一种传统的按照指令计数器规定的指令顺序来执行程序的计算机。
Programs are stored on permanent media (such as a hard disk), and loaded into RAM to be executed by the computer's processor, which executes each instruction in the program, one at a time.
程序储存于永久性介质（如硬盘）并加载随机存取内存而由计算机处理器执行，一次只执行程序内的一个指令。
Monmouth University's MBA program provides a high level of graduate instruction for successful business managers and professionals.
蒙茅斯大学的MBA项目提供了一个成功的商业管理人员及专业研究生教学的高水平。
A register in the processor that contains the address of the next instruction to be executed. Also known as a program counter.
包含下一条要执行指令地址的处理器中的寄存器。也叫程序计数器。
The flexible BIOS structure provides instruction stream to micro-processor, meanwhile program the components in the soft environment to create the test scenarios.
利用活芯BIOS结构给处理器提供指令流，同时通过编程验证环境中的组成单元来构造验证场景。
Sam: It's different from manual programming. After the programmer inputs simple instruction, the computer creates the program.
山姆：它跟手工编程不同。在程序员输入简单指令后，计算机自动生成程序。
If the following instruction is the target of a branch, the target program may crash.
如果下列指令的目标是一个分支，这个目标的计划可能会崩溃。
After example validating, the macro program wrote with macro instruction system designed in this dissertation can run well in open NC system.
经过实例验证，使用本文设计的宏指令系统编制而成的宏程序，完全可以在开放式数控系统上正确运行。
Real Programmers know every nuance of every instruction and use them all in every Real Program.
真正的程序员知道每一个指令的细微差别，并在程序中使用所有的指令。
Control unit (controller) : control unit is composed of program arithmometer, instruction register and operation controller, ect.
控制器：控制器是由程序计数器、指令存放器跟操作控制器等组成。
This paper analyses the return instruction of MCS-51 and gives the answer to releasing the interrupt. Some special use and program are also given.
分析了MCS一51单片机返回指令，解决了如何释放中断逻辑的问题，并给出一些特殊用法及实用程序。
This is primarily a direct instruction program.
这主要是直接教学计划。
According to Goldberg, the relative simplicity of the instruction makes this kind of program viable.
据戈德堡，相对简单的指令，使这种方案是可行的。
Rough cutting cycle instruction G71 is one of the commonly used instructions in manual Program of NC lathes.
数控车床内、外径粗车循环g71是数控车床手工编程中最常用的指令之一。
Rough cutting cycle instruction G71 is one of the commonly used instructions in manual Program of NC lathes.
数控车床内、外径粗车循环g71是数控车床手工编程中最常用的指令之一。
应用推荐