Crack: Read the Wikipedia entry for the classic UNIX password testing program.
Crack：阅读关于经典的UNIX密码测试程序的Wikipedia条目。
Apply the nonlinear GFEM to study the concrete crack problem, develop the corresponding program using the smeared crack model.
将非线性广义有限元法应用到混凝土开裂问题的研究，采用弥散裂缝模型，研制了相应的程序。
Under given crack dimensions and load condition, to appraise to cracks defects with fracture appraisal program and obtained submarine pipeline failure appraisal diagram (FAD).
在给定裂纹尺寸与载荷条件下，利用断裂评定程序对一裂纹缺陷进行了评定，得到了海底管线失效评定曲线(FAD图)。
It also discusses the reasonable se-lection and computation of structural parameters for arresting crack and burst and gives the computation program aided by computer design.
并讨论了止裂抑爆结构参敏的合理选择与计算，给出了计算机辅助设计计算的程序。
In this program the author adopt the viscoelastic-plastic unified constitutive theory, at the same time adopting the Kupfer-Gerstle destroy rule and mixed crack model.
将粘弹塑性统一本构理论引入程序中，同时采用了已经比较成熟的破坏准则和裂缝模型。
Taking the mine grouting project as an example, the program was applied to simulate the spreading scope of the grout in the crack network under the different grouting pressure.
以某煤矿注浆工程为例，采用该程序模拟了不同注浆压力下浆液在裂隙网络中的扩散范围。
The new analytical element can be implemented into FEM program systems to solve crack propagation for plane problems with arbitrary shapes and loads.
将该解析元与有限元相结合，构成半解析的有限元法，可求解任意几何形状和载荷的基于线性内聚力模型的平面裂纹扩展问题。
Based on the circumstance, the FORTRAN language was applied to write and prepare the flow expansion program of the grout within the non-connected crack network.
在此基础上，利用FORTRAN语言编制了浆液在非贯通裂隙网络内部的流动扩散程序。
A finite element program CCGC-1 is compiled to simulate the creep crack growth rate in materials working at elevated temperature.
编制了有限元程序CCGC - 1以模拟计算高温材料蠕变裂纹的扩展。
Experimental studies for crack growth of stiffened panels with multiple cracks were performed under both constant-amplitude load and program block spectrum load.
进行了恒幅谱载荷及程序块谱载荷下加筋板多裂纹的扩展试验研究。
The new analytical element can be implemented into FEM program systems to solve for stress intensity factor and deal with crack propagation problems for plane cracks with arbitrary shapes and loads.
将该解析元与有限元相结合，构成半解析的有限元法，可求解任意几何形状和载荷的平面裂纹应力强度因子及扩展问题。
Moreover, the program is also used to simulate and analyse the cavity and the surf ace crack during extrusion. Some curves and data for prediction of the above-mentioned defects have been worked out.
此外，还对轴对称正挤压时可能出现的中心缩孔和表面裂纹缺陷进行了模拟研究，得到了预测上述缺陷的曲线或数据。
The methods and the program can be used to guide the choice of milling cutter when processing the inner curve of pin gear housing in double crack three ring-plate cycloid reducer.
本文介绍的方法和编制的软件可用于指导现场中环板针齿壳内曲线加工铣刀的选取。
A finite element computer program for saturated soils was revised accordingly in order to be used in the analysis of crack formation and propagation upon drying on the clay surface.
相应的修改了饱和土的有限元程序，用于分析粘土表面干缩裂缝的形成过程。
A finite element computer program for saturated soils was revised accordingly in order to be used in the analysis of crack formation and propagation upon drying on the clay surface.
相应的修改了饱和土的有限元程序，用于分析粘土表面干缩裂缝的形成过程。
应用推荐