Principles of Computer Organization report on experimental micro-program controller.
计算机组成原理微程序控制器实验报告。
An approach of Micro program Controller design for coprocessor is put forward and a test bench is given to verify its function.
在微程序控制器的设计中提出一种协处理器微程序控制器的设计方法,并且给出其功能验证的测试平台。
PLC program controller ensure the stability of machine, which can store 120 sets function parameters, makes the production conveniently.
设备使用PLC程序控制,保证了设备运行的稳定。程序可储存120组功能参数,方便生产调用。
By adopting the C40P program controller from Japanese OMRON Co, this system can carry out electric control in the hot-banding machine for B/W CRT.
系统采用日本OMRON公司C40P型可编程序控制器实现黑白显像管热套式防爆机的电气控制。
This paper describes the program controller and the control system of distributing gear of a blast furnace with the application of magnetic logic elements.
本文主要介绍由磁性元件组成的高炉程序控制器及旋转布料器控制系统。
The brake reversing device not only can be controlled to operate by hands, but also can be controlled to operate by a program controller. The accuracy of the braking and the reversing is increased.
本装置既可使用手动控制工作又可使用程控器控制工作,极大地提高了制动换向的精确性。
This article talks about the design of a two-dimensional fuzzy controller which can use in radiation-convection mixed heating toughened furnace by the application of Mitsubishi Q02 program controller.
文章应用三菱q 02可编程控制器设计一个用于辐射-对流混合加热钢化炉的二维模糊控制器。
After installing the agent Controller on Linux, you need to launch the program for it to act as a listening agent.
在Linux中安装agentController以后,您需要启动程序以作为一个接听器。
Each program is also defined as a CICS transaction: QCTL for the controller and QMHD for the Message Handler.
每个程序也定义为一个CICS事务:QCTL作为控制器;QMHD作为消息处理器。
Controller values can be "captured" and stored as part of a program.
控制器值可以“捕捉”并储存的一个组成部分计划。
By designing the communication and back-end management software and simulated entrance guard controller program, we realized the centralized and distributed intelligent management.
通过设计通信和后台管理软件,以及模拟前端门禁控制器程序,实现了网络集中与分布式智能化的管理。
After correcting and optimizing the program, a tape punch can be connected to the CNC controller in order to obtain a revised version of the tape for future use.
纠正和优化方案后,纸带穿孔机可以连接到CNC控制器,以获得供将来使用的磁带的修订版本。
PID regulation in instrumentation circuit is realized by using program logic controller.
利用可编程序控制器实现仪表回路的PID调节控制。
This article describes a real-time controlling system of TV program auto-broadcasting with micro-computer PLC (Programmable Logic Controller).
本文叙述了一种用可编程序控制器进行实时控制的电视节目自动播放系统。
Crane operation of the various agencies to rely on the program control device to achieve, and now more than the use of a crane to control the programmable controller.
起重机各机构的运行要依靠程序控制装置来实现,现在起重机多使用可程序控制器来控制。
Programmable controller C20 is used in the program control of TIG automatic welding on manufacturing micro motor shell and stator core.
利用C20系列可编程序控制器对微电机加工制作中的定子铁心、电机壳体t IG自动焊接实现过程程序控制。
At last, the development of motion controller driver software and host application program is finished, and the results of the applied experiments show the CNC software system is satisfactory.
最后,我们完成了运动控制器驱动程序和开放式数控系统应用程序的开发工作,并在实际应用中取得了满意的效果。
Computer equipment and its control method, program, controller, system, card.
计算机设备及其控制方法,程序,控制器,系统,卡片。
The thesis presents a design program of the quick-start controller with electronic ballast, and the more in-depth theoretical analysis is finished.
本文提出了一种采用电子镇流器的快启控制器的设计方案,并进行了较为深入的理论分析。
The measures of improving the reliability of programmable controller application system were introduced, including the measures of program design and other.
全面介绍了提高可编程控制器应用系统的可靠性措施,包括程序设计和其它部分的可靠性的措施。
The paper described the collectivity function characteristic and several important components of movement controller, for example main control program, interpolation module and velocity control.
这里论述了运动控制器的总体功能特性,并分别介绍了运动控制器的几个重要组成部分,如主控程序、插补模块及速度控制等。
The hardware circuit and software program features of the given current, multi-pulsed resistance welding machine controller developed 8031 single chip processor are introduced in this paper.
本文介绍了用8031单片机研制的定电流,多脉冲电阻焊机控制器的硬件电路及软件程序的特点。
The design of the software includes three parts as following: the network communication between PC and controller, NAT9914 firmware and DLL (dynamic link library) program.
软件部分的设计共包括三大部分:PC机与控制器间的网络通信机制,NAT9914固件程序以及动态链接库程序。
Control unit (controller) : control unit is composed of program arithmometer, instruction register and operation controller, ect.
控制器:控制器是由程序计数器、指令存放器跟操作控制器等组成。
The pulse is directly read out by utilizing PLC high-speed counting module, the function of the locating controller can be achieved by program, thus the locating controller are saved.
利用PLC高速计数模块直接将外部编码器发出的脉冲读入,在PLC内部编程,通过程序控制完全能取代位置控制器的所有功能,从而省出位置控制器这一环节。
Microcomputer programming touch controller, high automatic program.
微电脑编程触摸控制器,自动化程序高。
PLC program design, signal processing between NC controller and PLC controller, as well as PLC and machine.
PLC控制程序的设计:包括数字控制器与PLC控制器之间、PLC与机床之间的各种信号处理等。
Multi module unit without adding any equipment can realize mutual linkage and program control, and the HIROMATIC controller can realize the remote network.
多模块机组无须增加任何设备即可实现互相联动及程序控制,通过HIROMATIC控制器即可实现远程联网。
With the CAD Program, controller is designed for the PWM system, Its realization shows good dynamic properties and that the design is valuable in engineering practice.
利用该方法为直流脉宽调速系统设计了控制器,并在实验室进行了实现,显示了良好的动态特性,表明控制器具有较大的工程实用价值。
This paper introduce the application of Siemens digital direct current timing device (6ra70) and program logical controller (SIMATIC S7-300) in piling bed electromagnet for the first time.
该文介绍了西门子全数字直流调速装置(6ra70)和可编程逻辑控制器(SIMATICS7- 300)首次在码垛电磁铁系统中的应用。
应用推荐